Vehicle safety management regulations 1
A, the car driver
1, strictly abide by the "Road Traffic Safety Law" and the relevant management rules.
2, the driver must carry a driver's license, drinking is not allowed to drive the vehicle, while driving is not allowed to smoke, eating and drinking, talking and laughing and any other actions that impede the safety, the cab is not allowed to sit in excess of the number of people.
3, before driving must check the vehicle brakes, steering wheel, horn, lighting signal lamps and other major devices are complete and intact, is strictly prohibited with sick car.
4, before driving, should check the surrounding obstacles, sound the horn to start.
5, in the upper and lower occupants, must do to stop and open the door, close the door to start.
6, in the driving, should always pay attention to pedestrians and vehicle dynamics, deceleration, the maximum speed shall not exceed 10 kilometers per hour, in and out of the factory gate, corner 5 kilometers; workshop, warehouse 3 kilometers; fork in the road to do a slow two look through three and sound the horn.
7, parking to choose the right place, no parking, should be designated places in order to park. After parking, you should remove the key and tighten the handbrake.
8, in the crane under the loading and unloading, the driver must leave the cab, not allowed at this time to check, repair the vehicle.
Second, vehicle repair safety regulations
1, before work to check the lifting equipment and tools performance is good.
2, repair the vehicle chassis, especially when dismounting tires, must be top stable jack, and cushion stable wooden pillow or iron bench.
3, repair forklift, etc., must be well padded with sleepers to support a good support frame.
4, test start before, should check the surrounding environmental conditions. Check for faults during operation, must always pay attention to the rotating parts, in order to prevent head and hand injuries.
5, where the need for a test drive, must be driven by a licensed personnel, test brakes, must be concentrated, pay attention to the car in front of the pedestrians, piles, and see the car behind the car with or without vehicles. Repair personnel without a driver's license is not allowed to drive a variety of vehicles. Only allowed to start in place.
6, test high-pressure sparks are not allowed to fill the oil inlet to prevent misfire.
7. In the event of an oil system failure, gasoline is not allowed to be used in direct flow or injected directly into the carburetor with a hose to start the engine.
8, the vehicle is strictly prohibited to take people for test drive, no standing on both sides of the cab, the vehicle is not parked, it is strictly prohibited to get on and off.
9, where the night on the way to repair the broken down vehicle, not allowed to use open flame lighting.
10, the vehicle must be gas cutting, welding open flame, prior to take fire prevention measures.
Three, tractor, forklift, tractor, forklift safety regulations
1, the driver must firmly establish the concept of safety first, to strengthen the sense of responsibility for safe driving, and strictly comply with these regulations.
2, the driver must have a driver's license, is strictly prohibited to drive without a license, the trainee driver in addition to the trainee license, there must be a formal driver with the car to teach.
3, a variety of production vehicles, there must be to ensure the safety of the sound device, large and small lights, directional lights, steering, brakes, etc. must be sensitive and reliable.
4, before traveling, should check the surrounding pedestrians or obstacles, sound the horn to start.
5, driving should pay attention to the dynamics of oncoming vehicles and pedestrians, the maximum speed shall not exceed 10 kilometers per hour, in and out of the factory gate, corner speed 5 kilometers per hour; workshops, warehouses 3 kilometers; fork in the road to do a slow two look three through.
6, traveling in the same direction of the vehicle, the distance between the front and rear of the two cars at least 10 meters above the rear car shall not overtake the front car.
7, vehicle turnaround, reversing must pay close attention to oncoming vehicles, pedestrians and the surrounding situation, slow speed.
8, with the occupants of the cab with a seat only allowed to sit two (including the driver), other parts are not allowed to ride, trailers are prohibited.
9, the vehicle in motion and not yet stopped, it is strictly prohibited for anyone to get on, off and pickpocket, jumping.
10, temporary parking at night in front of the workshop and intersections, should be open small lights, the driver shall not be far away.
11, vehicle loading and unloading objects under the crane, the driver must leave the cab to prevent falling objects hurt.
12, forklift operation forklift lift height shall not exceed the height of 2/3 of the vehicle, driving forklift height from the ground shall not be higher than 0.5 meters.
13, driving, prohibit smoking, eating and drinking, laughing or other obstacles to safe movement.
14, the driver must leave the vehicle with the switch key. After the work is completed, the vehicle must be braked, and take off the gear off, forklift shovel feet should be put down to the ground.
15, motor vehicles, such as major accidents, to protect the scene, timely report, by the relevant departments on-site observation and analysis before changing the scene.
Vehicle safety management regulations 2
Purpose:
In order to strictly manage the vehicle, the rational use of vehicles, cost savings, maximize the effectiveness of the use of vehicles to meet the company's official car needs.
Scope of application:
This system applies to all vehicles managed by the company.
Responsibilities:
1, conscientiously carry out the implementation of national and higher guidelines, policies and regulations on traffic safety, exemplary compliance with the company's "Vehicle Management System", strict self-discipline, set an example, and organize the specific implementation and inspection.
2, responsible for the company's vehicles road tax, vehicle tax and insurance payments for the work.
3, is responsible for the monthly convening of the company driver safety meeting, timely detection and elimination of potential safety hazards, sound driver safety and technical files, traffic accidents and machine damage accident records, vehicle mileage records and maintenance files, fill out all kinds of statements in a timely manner.
4, is responsible for verifying the driver reimbursement costs, in accordance with the uploaded vehicle budget cost indicators strictly control the use of vehicle costs.
5, the implementation of the traffic management department and the relevant units of the higher level of the vehicle technical management of the guidelines, policies, rules and regulations, responsible for the implementation of the traffic management department and the higher level to convey the spirit of the relevant documents.
6, the monthly organization of drivers for safety learning and professional ethics education, improve the driver's safety awareness and quality of thought.
7, is responsible for the establishment of a sound vehicle safety technology files, to complete the company's vehicle safety assessment indicators.
Responsible for the organization of the vehicle from time to time safety inspections, to carry out driver safety training, to maintain good vehicle performance, to eliminate potential accidents.
8, caring vehicles, abide by labor discipline, obey the scheduling, firmly establish the concept of safe driving, strict compliance with traffic safety regulations, to provide civilized, courteous, safe driving services.
9, establish a good sense of professional ethics and service consciousness, consciously do diligently check, diligent maintenance, keep the car neat and clean, keep the car in good condition, found faults should be reported and eliminated in a timely manner, do not drive a "sick" car.
10, actively participate in safety education activities, strict compliance with the company's rules and regulations, and seriously do a good job of parking the vehicle anti-theft anti-snatching and anti-vandalism measures.
11, the vehicle traffic accidents or accidents, should protect the scene, waiting for the traffic police department to deal with, and notify the administrator and unit leaders.
12, without the approval of the company's leaders in charge, may not give the vehicle to non-full-time driver. Each trip to carefully fill out the "Vehicle Traveling Record Sheet".
13, the vehicle can only be in the company's designated gas station refueling, because of the need to work to buy fuel, must be agreed by the vehicle administrator.
14, the driver in the handover of vehicles, must check their respective vehicles, found that the problem promptly reported to the vehicle administrator, otherwise found that the damage is borne by the driver on duty.
15, it is strictly prohibited to drive the vehicle without a license and private car, violators will be dismissed.
16, the deployment of vehicles to the jurisdiction of the road outside the area of business, must be approved by the company in charge of leadership.
The annual review of the vehicle, maintenance and repair unified by the Ministry of Integrated Affairs vehicle administrators to arrange for the driver to fill out the "Vehicle Repair and Maintenance Application Form", in accordance with the provisions of the approval before entering the factory for repair. If beyond the maintenance content, the costs incurred by the driver to bear. In special cases, if the maintenance needs to be done nearby, the vehicle administrator will agree to do the maintenance only after approval.
Vehicle safety management regulations3
1, general rules
1, 1 in order to strengthen the plant (hereinafter referred to as the plant) motor vehicle safety management, to improve the safety and technical condition of the plant motor vehicle, to protect the safety of the operation, according to the relevant provisions of the state, the formulation of the provisions of this...?
1,2 the provisions of this referred to in-plant motor vehicles, refers to limited to the scope of the plant (including outside the plant yard and other production and operation areas and operation sites) traveling and operation of motor vehicles.?
2, safety technology requirements?
2.1 vehicles should be neat and tidy, body circumference. Vehicle equipment, safety devices and accessories should be complete and effective. Vehicle safety management system.
2, 2 vehicle technical condition, pollutant emissions, noise should be consistent with the relevant national standards and regulations.
2,3 all parts of the vehicle in the engine running and stopping should be no oil leakage, water leakage, electricity leakage, gas leakage phenomenon.
2.4 The hydraulic system of the vehicle should have smooth piping and good sealing; no deformation of the operating lever, no jamming; the distributor components are well matched, and the safety valve is sensitive and reliable; the working parts should not be creeping, stagnation and obvious impulse phenomenon within the range of the rated speed.
2, 5 vehicle engine should be installed firmly and reliably, good power, smooth operation, no abnormal noise, good starting and stopping performance.
2, 6 engine starting system, ignition system, fuel system, lubrication system, cooling system should be complete, good performance, firmly installed, lines, pipelines do not wear touch.
2.7 The maximum free rotation of the steering wheel of the vehicle shall not be more than 30 degrees from the center position to the left and right.
2, 8 vehicle steering should be light and flexible, driving shall not be light, swing vibration, shaking, blocking and running phenomenon. Vehicle safety management system. On a straight road can keep the vehicle straight, steering can automatically return to the right after.
2.9 The steering wheel steering force of the vehicle and the amount of side slip of the front wheels shall comply with the relevant standards and regulations.
2, 10 front wheel alignment value should be consistent with the design provisions.
2, 11 steering gear shall not lack of oil, oil leakage, fixed bracket must be firm. Steering arm, horizontal tie rod and other steering parts shall not be welded together, cracks, deformation. Ball head and ball seat, steering knuckle pin and bushing with the right amount of tension, well lubricated.
2, 12 vehicles and trailers must be set up independent of each other driving and parking brake, brake parts should be intact and effective.
2.13 The braking force, reserve travel, free travel of the pedal and brake release time and other indicators of the running brake should be consistent with the relevant standards, regulations and technical conditions of the vehicle.
2, 14 pneumatic braking system technical indicators should be consistent with the relevant standards and regulations, must be equipped with a water discharge device and pressure limiting device.
2.15 Mechanical brakes, tie rods and other parts should be intact.
2, 16 in the process of vehicle operation, there should be no self-braking phenomenon.
2,17 The braking distance, run-out, parking brake performance requirements of the vehicle should be in accordance with the relevant standards and regulations.
2, 18 vehicle lighting and indicator lamps should be installed firmly, complete and effective. Bulbs should have a protective device, not due to vehicle vibration and loose, damage, failure or change the direction of light. All light switch should be installed firmly, switch freely, not due to vehicle vibration and switch itself.
2, 19 vehicles should be equipped with a horn, its performance should be reliable, the volume of the horn should be in line with the relevant standards of noise regulations.
2.20 The vehicle's various meters should be complete and sensitive and effective.
2, 21 vehicle tire inflation pressure should be consistent with its technical performance requirements. Partial wear of the tire tread shall not expose the tire cord fabric layer.
2, 22 vehicle tires on the same axle should be the same type and tread. The steering wheels of the vehicle shall not be fitted with retreaded tires.
2.23 The steel plate spring of the vehicle shall not be cracked, broken or missing, and its center bolt and u-bolt shall be tightened.
2, 24 shock absorbers should work properly. The frame shall not be deformed, rusted or bent, and the bolts and rivets shall not be missing or loose. Front and rear axles shall not have deformation, cracks.
2.25 The clutch of the vehicle shall be smoothly engaged and thoroughly disengaged, and there shall be no noise, shaking or slipping. The pedal force and free travel shall be in accordance with the relevant standards and regulations and the relevant technical conditions of the vehicle.
2.26The transmission should be free of cracks, flexible and lightweight, reliable self-locking and interlocking, and no deformation of the gearshift.
2, 27 drive shaft universal joints should be free of cracks and deformation, complete and reliable locking; transmission is smooth, in operation, no vibration and noise.
2,28 the technical condition of the cab should be able to ensure that the driver has normal labor conditions.
2, 29 vehicle cab must have a good line of sight, the windshield shall not use plexiglass and ordinary glass. Must be equipped with mirrors, wipers.
2, 30 fuel tanks and fuel lines should be strong and protective devices to prevent damage and oil leakage due to vibration and impact. Fuel tank and exhaust pipe should be located more than 300mm apart or set up effective heat insulation. The fuel tank should be more than 200mm away from the exposed electrical connectors and electrical switches.
2.31 Vehicles transporting flammable and explosive substances must be equipped with fire-fighting equipment and appropriate safety measures.
2.32 Vehicles entering flammable and explosive places of operation must have explosion-proof measures.
2, 33 types of plant motor vehicles should also comply with their own unique safety conditions and requirements.
3, safety management
3, 1 vehicle units should strengthen the safety management of the plant's motor vehicles to ensure the safe operation of the plant's motor vehicles.
3,2 the company, the car-using units should establish and improve the plant motor vehicle safety management rules and regulations, and seriously implement.
3, 3 plant motor vehicles should be set up by each unit of safety and technical management files, the contents of which include:
3, 3, 1, the vehicle factory technical documents and product certification;
3, 3, 3, 2, the use of maintenance, repair and self-inspection records;
3, 3, 3, 3, the safety and technical inspection reports;
3, 3, 4, vehicle Accident records.
3,4 Dispatch Department, the Department of Safety is responsible for the Company's plant motor vehicle safety supervision and inspection.
3, 5 in use, new and modified plant motor vehicles should be used by the Department of Dispatch and the vehicle unit to the location of the plant motor vehicle management department for registration, the establishment of vehicle files, by the competent authorities of the vehicle safety and technical inspection and certification of license plates before use.
3.6 The license plate of the in-plant motor vehicle is designed and supervised by the management department.
3, 7 plant motor vehicles in case of transfer, modification, scrapping, etc. should be timely to the competent authorities in the location of the registration procedures.
3, 8 plant motor vehicle drivers are special operators, by the local and municipal quality and technology supervision and management departments to organize the examination and issuance of certificates.
3, without the approval of the general manager of the company (except in special circumstances), may not take the car. Those who privately take the car as a substitute will be punished more severely.
4, safety and technical inspection?
4, 1 company car units should be plant motor vehicles for annual, quarterly, monthly and daily inspection.
4, 2 scheduling department, the Department of Safety in the car unit on the basis of self-inspection of the plant's motor vehicles for annual inspection. Failed inspection of the vehicle by the Department of Dispatch, the Department of Safety deadline for rectification, and be re-inspected.
4, 3 plant motor vehicles repair, modification must be applied to the Department of scheduling inspection, qualified before use.
5, penalties?
5,1 for violation of this provision of the unit, the dispatch department, the security department may, depending on the severity of the case, and in accordance with the relevant provisions, were given notice, driving, driving suspension, fines and penalties.
5,2 The inspectors who neglect their duties and show favoritism in the inspection work shall be investigated and punished according to the relevant regulations.
6, bylaws
6.1 This regulation is supervised and implemented by the Safety Department.
6.2 The vehicle-using units may formulate the implementation methods according to these regulations.
6,3 These provisions shall come into force on the date of publication.
Vehicle safety management regulations related articles :
1. 3 motor vehicle management regulations
2. vehicle safety management inspection system
3. vehicle safety inspection management system
4. vehicle parking safety management system
5. distribution vehicle safety management system
6. Traffic safety management rules and regulations