What about the dangerous goods transport certificate? Conditions for handling dangerous goods transport certificate
1. Having a general freight service qualification certificate and working for more than 2 years;
2. There is no major accident certificate within 3 years (this requires you to find a company with dangerous goods transportation qualification to open a certificate file for you);
Third, go to the traffic control department where this company is located and stamp it to confirm that you have no major accidents within three years;
Fourth, take this certificate and apply to the transportation management office (bureau) of the county where the enterprise is located for an increase;
5. The cost of waiting for the notice to participate in the training is about 1200 (including the textbook fee). Bring a copy of the driver's license, * * * *, a copy of the general cargo transport qualification certificate, and three photos of white background 1 inch to the freight section of the Transportation Bureau for registration.
What about the dangerous goods transport certificate?
The following 19 materials shall be provided to apply for a business license for road transport of dangerous goods. Please submit a document in the following order to ensure that its contents are true and effective, and formally submit it in duplicate after the first trial is correct:
Detailed opinions on the application materials:
0 1: notice of pre-approval of enterprise name issued by the administrative department for industry and commerce.
02: Application Form for Road Dangerous Goods Transportation Management, appendix 1 to be filled in by the applicant by computer, including the basic information of the applicant, the scope of dangerous goods to be transported (category, articles or name, if it is a highly toxic chemical, it should be marked as "highly toxic") and other contents.
04: Power of Attorney for Enterprise Application for Registration: Appendix 2 shall be filled in by the applicant.
05: Materials to prove the condition of special vehicles and equipment.
(1) For the vehicle to be put into operation, please fill in the Letter of Commitment for the Vehicle to be put into operation in Annex 3 (the vehicle to be put into operation refers to the case that the industrial and commercial business license has not been applied). If special vehicles or equipment are not purchased, a commitment letter for investment in special vehicles or equipment shall be submitted. The contents of the letter of commitment shall include quantity, type, technical level, total mass, approved load mass, number of axles and overall dimensions of vehicles; Equipped with communication tools and satellite positioning equipment; Tank volume of special tank car; The matching between the total mass of the tank body of the special tank vehicle after loading and the approved loading mass of the vehicle; Information on the approved loading quality of special vehicles for transporting highly toxic chemicals, explosives and explosive dangerous chemicals. The commitment period shall not exceed 1 year. (For vehicle equipment requirements, please refer to "▲ Vehicle and Equipment Requirements" below)
(2) The vehicle has been purchased or existing (the vehicle has been purchased or existing, indicating that the applicant has obtained the industrial and commercial business license, and the name of the vehicle driving license is the same as that of the industrial and commercial business license, and only the professional transportation of dangerous goods is added on the basis of the original business scope of the industrial and commercial business license). If a special vehicle or device has been purchased, it shall provide the vehicle driving license, vehicle technical grade certificate or vehicle comprehensive performance testing technical certificate; Equipped with communication tools and satellite positioning devices; Tank inspection certificate or inspection report and copy of tank special vehicle and other related materials. (For vehicle equipment requirements, please refer to "▲ Vehicle and Equipment Requirements" below)
▲ Requirements for vehicles and devices applying for transporting dangerous goods:
(1) more than 5 own special vehicles (except trailers); Transport highly toxic chemicals and explosives, and own special vehicles (except trailers) 10 or above.
(2) The technical performance of special vehicles meets the requirements of the national standard "Comprehensive Performance Requirements and Inspection Methods for Operating Vehicles" (GB 18565); The technical level has reached the first-class technical level specified in the industry standard Technical Grade Classification and Evaluation Requirements for Operating Vehicles (JT/T 198).
(3) The overall dimensions, axle load and mass of special vehicles meet the requirements of the national standard "Limits of Overall Dimensions, Axle Load and Mass of Road Vehicles" (GB 1589).
④ The fuel consumption of special vehicles meets the requirements of the industry standard "Fuel Consumption Limits and Measurement Methods for Operating Freight Cars" (JT7 19).
⑤ Equipped with effective communication tools.
⑥ Special vehicles should be equipped with satellite positioning devices with driving record function.
All landowners transport toxic chemicals, explosives, explosive dangerous chemicals, should be equipped with special containers such as tanks, trucks or pressure vessels.
The tank of a special tank vehicle shall be inspected by the quality inspection department, and the total mass of the tank after loading shall match the approved loading mass of the special vehicle. The tank volume of special tankers for transporting explosives and highly corrosive dangerous goods shall not exceed 20 cubic meters, and the tank volume of special tankers for transporting highly toxic chemicals shall not exceed 10 cubic meters, except for tank containers that meet the relevant national standards.
Pet-name ruby transport of highly toxic chemicals, explosives, corrosive dangerous goods, the approved load quality shall not exceed 10 tons, except for container transport vehicles that meet the relevant national standards.
Attending equipped with safety protection, environmental protection and fire control facilities and devices suitable for the nature of dangerous goods transported.
06: The commitment letter of empty car parking refers to the applicant's commitment not to park dangerous goods professional transport vehicles.
07-08: Summary roster of drivers, loading and unloading managers and escorts who have been hired/planned to be hired specially for the transport of dangerous goods. Please see Annex 6 for the roster; Original and photocopy of the identity cards and qualification certificates of drivers, loading and unloading managers and escorts who specialize in the transport of dangerous goods; Original and photocopy of driver's license for professional transport of dangerous goods; Original and photocopy of employment contract for safety production of all employees. To hire drivers, loading and unloading managers and escorts, submit a letter of commitment, and the commitment period shall not exceed 1 year;
▲ Requirements for drivers, loading and unloading management personnel and escorts:
(a) the driver of the car has obtained the corresponding motor vehicle driver's license, and the age is not more than 60 years old.
(2) Drivers, loading and unloading managers and escorts engaged in the road transport of dangerous goods shall pass the examination by the transportation department of the municipal people's government with districts where they are located, and obtain corresponding qualification certificates; Drivers, loading and unloading managers and escorts engaged in road transport of highly toxic chemicals and explosives shall pass the examination and obtain qualification certificates marked as "transporting highly toxic chemicals" or "transporting explosives".
③ The number of escorts and drivers should be more than the number of existing vehicles and vehicles to be purchased 10%~20%. If the dangerous goods transport enterprise plans to purchase 5 vehicles, there should be at least 6 escorts and 6 drivers each.
09: Provide effective communication tools for each type of work and vehicle. If you want to buy a vehicle, please promise to equip the vehicle with effective communication tools in the vehicle commitment letter.
10: Feasibility report of establishing a company, including soft environment, company profile, feasibility and advantages of establishing a company, risks of establishing a company and countermeasures to avoid risks, etc.
1 1: Categories, items and operation plans for transporting dangerous goods. Please explain the categories, items and operation plans of dangerous goods transported by yourself. (Please refer to Annex 4 for categories and items. For example, combustible gas belongs to the second category; Please also provide the operation plan of dangerous goods transportation).
15: company personnel roster and copy of ID card. The applicant shall fill in Appendix 5 of the company roster and submit a copy of the valid ID cards of all employees of the company.
16: the enterprise should be equipped with full-time safety management personnel, and provide the letter of appointment, the original certificate and a copy of the hired safety officer; If it is to be employed, the original and photocopy of the letter of commitment to be employed shall be submitted, and the commitment period shall not exceed 1 year; Training can be organized by the competent department in the later period of the certificate of safety officer, and at least one full-time safety officer should be equipped for every 20 vehicles.
17: equipped with safety protection, environmental protection and fire-fighting facilities and devices suitable for the nature of the transported dangerous goods (attached with a list and reviewed by the county-level competent department, and issued a certificate of conformity).
18: site lease contract. The land lease contract is a lease contract for office space and parking lot for at least 3 years. Self-owned land should provide proof of its own land property rights.
▲ Parking requirements:
(1) Parking lots owned or leased for more than 3 years that are suitable for the business scope and scale shall be located in the municipal administrative area where the enterprise is registered.
(2) Special vehicles and tank-type special vehicles for transporting highly toxic chemicals and explosives, with the number of less than 20 vehicles (inclusive), the parking area shall not be less than 1.5 times of the vehicle's orthographic projection area, and the parking area of each vehicle shall not be less than the vehicle's orthographic projection area if the number is more than 20 vehicles. Transport other dangerous goods, the number of special vehicles is below 10 (inclusive), and the parking area is not less than 65438+ 0.5 times of the orthographic projection area of vehicles; If the number exceeds 10, the parking area of each vehicle shall not be less than the orthographic projection area of the vehicle.
(3) The parking lot shall be closed and clearly marked, and shall not interfere with residents' life or threaten public safety.
19: The preparation of the safety production management system shall include the following contents.
(1) The responsibility system for production safety of the principal person in charge of the enterprise, the person in charge of the safety management department and the full-time safety management personnel.
(2) Employee responsibility system for production safety.
③ Safety production supervision and inspection system.
④ Safety production education and training system.
⑤ Safety management system for employees, special vehicles, equipment and parking lot.
⑥ Emergency rescue plan system.
All landowners safety production operation procedures.
⑧ Safety production assessment and reward and punishment system.
Pet-name ruby safety accident reporting, statistics and handling system.
▲ Others:
(1) The offices and factories or parking lots of dangerous goods enterprises should be located in the same county.
(2) Special vehicles such as oil tankers need to be repaired in professional repair shops, while other vans only need more than two types of repair shops.
Dangerous goods can be transported on the highway, but your car must be in good condition.
Basic requirements for transport vehicles
(1) Any unit engaged in the transportation of dangerous crystal articles on the expressway must have facilities and devices that can ensure the transportation safety of dangerous articles.
① Basic requirements for motor vehicles.
A. The bottom of the cargo hold should be made of wood floor, and the surrounding baffles must be firm. This is because most dangerous goods are flammable and explosive, and the wooden floor can avoid sparks and is safer. When transporting inflammable and explosive dangerous goods with iron bottom cars, corresponding gasket protection measures should be taken. The carriage must be kept clean and dry. After the goods are unloaded, there shall be no residue in the carriage.
B the exhaust pipes of motor vehicles must be equipped with devices for heat insulation and extinguishing Mars, and the electrical system should be equipped with devices for cutting off power supply.
② Basic requirements for tank cars.
Page 182
A The materials of tanks (boxes) for transporting dangerous goods must be suitable for the nature of the goods. Usually: carbon steel tank cars can use dangerous goods such as concentrated sulfuric acid and lye; Nitric acid should use aluminum cans (the tank cover should be sealed with gaskets to prevent leakage). Hydrochloric acid, hypochlorous acid and waste nitric acid should be made of FRP or stainless steel.
B the tank (box) for transporting dangerous crystal goods should have sufficient strength, and be equipped with corresponding safety devices such as two-way valve pressure relief brake, corrugated board, sunshade, pressure gauge and liquid level meter according to the needs of different goods, so as to ensure that the loaded goods do not leak. Not all the above equipment are installed, but they are equipped according to actual needs. Such as flammable liquids (gasoline, benzene, etc.). ) must be equipped with electrostatic safety device. Because the movement of flammable liquid will produce static electricity during transportation, it is necessary to install a special rubber mop at the rear of the car to conduct static electricity; For example, in summer and hot season, those dangerous goods that are afraid of sun exposure or high temperature must be covered with sheds or corresponding awnings.
C. The installation and use of liquefied petroleum gas tank cars (tanks) must meet the requirements of the Regulations on Safety Management of Liquefied Petroleum Gas Tank Cars issued by the State Administration of Labor.
D vehicles carrying containers, large gas cylinders (500-2000 ks liquid chlorine, liquid ammonia and other gas cylinders) and movable tanks (boxes) (temporarily lifted tanks) must be equipped with effective fastening devices and corresponding wooden plugs.
③ Special transport vehicles and devices for transporting radioisotopes shall comply with the relevant provisions of the health and epidemic prevention departments or public security departments of provinces (municipalities and autonomous regions), and shall regularly check the radioactive pollution of vehicles, devices, means of transport and protective articles. When the pollution exceeds the allowable level, it shall not be used again. If the radioactive intensity of pollution exceeds 50 micro curies or the relative radioactive intensity exceeds 2 micro curies kilograms, or the surface radiation level exceeds 0. 5 millirem, it must be cleaned and disinfected before it can be used again.
4 traffic.
A Vehicles transporting dangerous goods on the expressway must strictly abide by traffic, fire protection, public security and other laws and regulations. The speed should be controlled according to the actual road conditions, and a safe distance should be kept from the vehicles in front. It is forbidden to overtake illegally and stop at will, try to avoid emergency braking and ensure driving safety.
B Vehicles transporting dangerous goods should keep a safe distance from the vehicle in front when passing through toll stations, ramps, large bridges and interchanges, and slow down.
C dangerous goods restricted in transportation in summer and hot season shall be implemented in accordance with the relevant regulations of the traffic police department of the expressway.
D vehicles loaded with dangerous goods are not allowed to park at highway toll stations and service areas at will. If loading and unloading operations or temporary parking must be carried out at the above locations, corresponding safety measures shall be taken with the consent of the highway traffic police department.
E it is forbidden to transport explosives, radioactive substances, toxic compressed gas and liquefied gas through the expressway service area; If you must enter the service area, you should report to the traffic police department of the expressway for approval in advance and drive according to the specified route and time.
F transport of dangerous goods must be accompanied by a special person; When transporting explosives, highly flammable and toxic substances, the consigning unit must send personnel familiar with the nature of the goods to guide the operation and escort them with the vehicle.
G vehicles transporting dangerous goods are prohibited from taking irrelevant personnel; Always check all kinds of instruments on the way. When problems are found, measures should be taken in time. If it cannot be solved, you should choose an appropriate area to stop driving and report to the highway traffic police department and the highway management unit in time.
H. If dangerous goods are lost or stolen in transit, they should immediately report to the highway traffic police and the highway management unit for investigation. This is because the loss or theft of dangerous crystal articles may cause serious consequences, which must be reported in time and must not be concealed. Once serious consequences are caused, the relevant personnel will be investigated for legal responsibility.
What is the identification of occupational hazard factors? Under the guidance of scientific occupational health theory, the identification of occupational hazard factors is to identify, identify, analyze and predict the location, mode, occurrence mode and change law of occupational hazard factors in construction projects and workplaces with scientific methods, and to describe them accurately, express them clearly with qualitative and quantitative concepts and explain them with logical theories. The classification of occupational hazard factors can usually be classified according to their sources, or refer to the Catalogue of Occupational Hazard Factors promulgated by the Ministry of Health. 1. According to the sources of occupational hazards, it can be divided into three categories: ① Harmful factors in the production process, mainly including chemical factors, physical factors and biological factors. Chemical factors mainly include productive poisons (such as metals and nonmetals, * * * gases, asphyxiating gases, etc. ) and productive dust (such as silica dust, coal dust, asbestos dust, etc. Physical factors mainly include abnormal meteorological conditions (such as high temperature, high humidity, low temperature, high and low air pressure, etc.). ), noise and vibration, ionizing radiation (such as x-rays, gamma rays, etc.). ) and non-ionizing radiation (such as visible light, ultraviolet light, infrared light, radio frequency radiation, laser, etc. ). Biological factors mainly include Bacillus anthracis, Brucella, forest encephalitis virus, fungi and parasites. ② The harmful factors in the labor process mainly include unreasonable labor organization and system; The work and rest system is unreasonable; Excessive labor intensity or improper production quotas; Mental (psychological) occupational stress; Excessive stress in individual organs or systems; Being in a bad state for a long time or using unreasonable tools. (3) Harmful factors in the production environment mainly include harmful factors in the natural environment, such as heatstroke caused by long-term solar radiation in hot seasons; And the building or layout of the factory building is unreasonable, such as insufficient lighting, poor ventilation, toxic and non-toxic, high-toxic and low-toxic operations arranged in the same workshop. There is also air pollution in the working environment. The second is the classification of occupational hazards listed in the Management Measures for Classification of Occupational Hazards in Construction Projects and the Catalogue of Occupational Hazards promulgated and implemented by Order No.49 of the Ministry of Health in 2006. The measures stipulate that the factors that may cause serious occupational hazards include the following contents: ① chemical factors listed in the Catalogue of Highly Toxic Substances; (2) asbestos fiber dust and dust containing more than 65438+/-00% free silica; ③ Radioactive factors: nuclear facilities, irradiation processing devices, accelerators, radiotherapy devices, industrial flaw detectors, oilfield logging devices, Class A open radioisotope workplaces, radioactive material storage and other devices or places; (4) Other factors stipulated by the Ministry of Health that should be included in the scope of serious occupational hazards. The measures also stipulate that projects that may cause occupational hazards refer to projects that have or produce occupational hazard factors listed in the Catalogue of Occupational Hazard Factors. According to the classification catalogue of occupational hazards, it can be divided into the following 10 categories: ① dust category. Including silicon dust, coal dust, asbestos dust, talc dust, cement dust, aluminum dust, welding dust, casting dust and other dust. ② Radioactive substances. Including all kinds of radioactive substances and other radioactive injuries that may lead to occupational diseases. ③ chemical substances. Include lead, mercury, manganese, cadmium, vanadium, phosphorus, arsenic, hydrogen arsenide, chlorine, sulfur dioxide, phosgene, ammonia, nitrogen oxides, carbon monoxide, carbon disulfide, hydrogen sulfide, benzene, dichloroethane, nitrobenzene, acrylamide and the like. ④ Physical factors. Include high temperature, high pressure, low pressure, local vibration, etc. ⑤ Biological factors. Include Bacillus anthracis, forest encephalitis virus and Brucella. ⑥ Risk factors leading to occupational diseases. Including contact dermatitis, photosensitive dermatitis, electro-optic dermatitis, acne, ulcers, chemical panel burns and other occupational panel diseases. ⑦ Risk factors leading to occupational eye diseases. Including chemical eye burns, electro-optic ophthalmia, occupational cataracts and other harmful factors. ⑧ Risk factors leading to occupational otorhinolaryngology and oral diseases. Including noise deafness, chrome nose disease, tooth erosion and other harmful factors. Pet-name ruby risk factors leading to occupational tumors. Include asbestos, benzidine, benzene, chloromethyl ether, arsenic, vinyl chloride, coke oven waste gas and chromate. Attending other occupational hazards. Including zinc oxide, toluene diisocyanate, cotton dust and harsh working conditions. The identification methods of occupational hazard factors mainly include comparative experience method and detection and inspection method. Comparative experience method is that the appraisers identify and analyze the possible occupational hazards in the project to be evaluated according to their own practical work experience and relevant professional knowledge, laws, regulations and standards related to occupational health, and with the help of experience and judgment ability. According to the requirements of relevant national technical specifications and standards, the evaluator of inspection methods evaluates the concentration or intensity of occupational hazard factors in the workplace and the protective effect of occupational hazard protection facilities through on-site inspection and laboratory analysis.
It is very simple to define the types of occupational hazards in workplaces, posts and workers.
What are the occupational hazard factors determined according to national standards?
1, hygienic standard for design of industrial enterprises gbz l-2010;
2. Hazardous factors in the workplace occupational exposure limits Part 1 Part: Chemical hazardous factors GBZ 2.1-2007;
3. occupational exposure limits of Hazardous Factors in Workplace Part 2: Physical Factors GBZ 2.2-2007；; ;
etc
First of all, we have to identify whether it is on it.
Some don't, but there are detection methods, so we should refer to the standards of other countries.
The standard of detection method gives several examples:
Determination of sodium and its compounds in the air of workplace (GBZ/T160.18-2004);
8. Determination of Inorganic Carbon Compounds in Workplace Air (GBZ/T160.28-2004);
9. Determination of Inorganic Nitrogen Compounds in Workplace Air (GBZ/T160.29-2004);
10, Determination of Toxic Substances Sulfide in Workplace Air GBZ/T160.33-2004;
1 1, determination of fluoride in the air of workplace gbz/t160.36-2004;
12, determination of chloride in workplace air gbz/t160.37-2004;
13, determination of mixed hydrocarbons in workplace air gbz/t160.40-2004;
14, determination of aromatic hydrocarbons in the air of workplace gbz/t160.42-2007;
15, determination of alcohol compounds in the air of workplace gbz/t160.48-2007;
16, Determination of Fatty Aldehydes in Workplace Air GBZ/T160.54-2007;
17, determination of fatty ketones in the air of workplace gbz/t160.55-2007;
18, Determination of Nitrile Compounds in Workplace Air GBZ/T160.68-2007;
19, Measurement of Physical Factors in Workplace Part 8: Noise GBZ/T189.8-2007;
20. Determination of dust in the air of workplace Part 1: Total dust concentration GBZ/T192.1-2007;
2 1 Determination of dust in the air of workplace Part 2: Breathable dust concentration gbz/t192.2-2007;
etc
The relationship between occupational hazards and occupational diseases Occupational hazards: dangerous and harmful factors in the working environment; Occupational hazards: diseases directly caused by exposure to occupational hazards.
What are the occupational hazards of listening to noise? Noise up to 80dB constitutes an occupational hazard.
From the point of view of occupational health, there are sounds harmful to hearing and health or other hazards, and the operation with equivalent sound level of 8 hours a day or 40 hours a week is called noise operation.
In the process of occupational disease identification, only workers engaged in noise operations can be diagnosed as occupational noise deafness. According to the regulations of physical factors, the limit of steady noise is 85dB(A), and the equivalent sound level of unsteady noise is 85dB (a). The working day per week is not 5d, so the equivalent sound level of 40h needs to be calculated, and the limit value is 85 dB(A). Basically, when the 8-hour equivalent continuous A sound level in the working environment of an enterprise is greater than 80dB, employees need to undergo noise-related occupational health examination, and when it is greater than 85, they need to be equipped with personal protective equipment such as earplugs.
Dangerous goods transport vehicles Dangerous goods transport vehicles are special vehicles, and dangerous goods enterprises must apply for safety licenses. In the safety license, there is a review of the qualifications related to the transportation of dangerous goods. However, for special vehicles for dangerous goods, only the regulations of the transportation department need to be met, and enterprises can file with the safety supervision department!
This is my opinion, I don't know if it's right! For details, please visit the following website:
:chinazyqc。 /technology/policy/
Cold hazard-freezing dangerous goods to transport liquids? You need a freezer to fully refrigerate ~
I don't do it now ~ it used to be like this. I'd like to introduce you to my former company, which specializes in dangerous goods. The company has its own dangerous goods declarer and cooperative dangerous goods warehouse. .
Zhejiang Yongtai International Freight Forwarding Co., Ltd. ~ ~ If you leave Ningbo Port.