1, the machine is installed near the water source, drainage should be convenient;
2, the machine installation location will not affect the user's other daily operations
3, the machine and piping installed in the place will not be subjected to direct sunlight;
4, as far as possible to be installed in the place of the drainage drain, and other facilities, such as the kitchen, bathroom, avoiding installation with wooden floors or near valuable items;
Two: in the selected host installation location with a marking pen to mark the installation. For example, in the kitchen, bathroom, avoid installation in the wooden floor or valuables near;
Two: in the selected host installation location with a marker pen to mark, with an electric hammer to punch holes, will be fixed to the wall with expansion screws hanging plate. (Kitchen under the installation of this step can be omitted)
1, hanging plate holes should be horizontal, can not have the naked eye can detect the phenomenon of skew;
2, hanging plate screws must be tightened to withstand the weight of the machine;
three: the face of the host will be open, the host of the water system will be hung on the hanging plate. (Kitchen under the installation of gooseneck faucet after the installation of the water production host will be placed outside the cabinet to facilitate the operation of the location)
Four: Installation of pre-treatment cartridge (refers to the bare machine under the kitchen) will be equipped with pre-treatment cartridges in accordance with the order of the installation of the PP-granular activated carbon carbon rods
1, pay attention to the number of levels of cartridges (the market is generally 5 levels) and the sequence of order;
2, the granular activated carbon The end with the sealing ring is facing up;
3, tighten the bottle, pay attention to: first gently shake the bottle to feel no resistance before completely tightened to prevent the cartridge is not centered to lead to internal leakage;
4, tighten the bottle, pay attention to the O-ring do not damage, if the O-ring is easy to fall, please give the O-ring touch a little Vaseline;
Five: Installation of water inlet tee and water inlet ball valve
1, according to the user's actual situation and the water inlet ball valve
2, the water inlet valve is installed in the water inlet and water inlet valve
2, the water inlet valve is installed in the water inlet and water inlet valve. p>1, according to the user's actual situation, close the user's total water valve or cabinet inside the angle valve, open the user's faucet will be inside the pipeline to remove the pressure;
2, according to the actual installation location, spin down the user's faucet or cabinet inside the cold water connection hose, will be randomly fitted with the water inlet tee thread wrapped around a good raw material tape, connected to the water pipeline; will be a small water ball valve thread wrapped around a good raw material tape, connected to the water pipeline; will be a small ball valve thread wrapped around a good raw material tape, connected to the water pipeline. Wrap the raw material tape around the outer thread of the water inlet tee and connect it to the inner thread on the side of the water inlet tee; install the tap or connecting hose back;
3. Close the water inlet ball valve, open the main valve of the water supply or the angle valve under the cabinet, and conduct a leakage test on the water inlet tee that has just been installed, and check whether there is any water leakage or seepage phenomenon;
4. Connect the machine's water inlet to the small water inlet ball valve (don't open the small ball valve for the water inlet).
5, the water inlet tee must be connected to the cold water pipeline (to prevent misconnection to the hot water pipeline leading to RO membrane damage).
Six: Installation of gooseneck faucet
1, according to the user's actual situation, select the gooseneck faucet fixing method (countertop installation or wall mounted installation);
2, in the selected location of the hole, the gooseneck faucet will be fixed;
3, will be connected to the gooseneck faucet on the one end of the PE pipe and the other end is connected to the water purifier's purification port.
Seven: Installation of the pressure drum
1, in the pressure drum inlet wrapped around the raw material tape
2, the pressure drum ball valve screwed to the pressure drum;
3, the pressure drum ball valve screwed in can not be skewed, to prevent the plastic threads slippery threads;
4, the pressure drum ball valve can not be screwed too tightly, to prevent damage to the ball valve.
Eight: rinse the front activated carbon and RO membrane
1, rinse off the activated carbon cartridge charcoal powder, rinse off the surface of the RO membrane of the protective fluid, repeat 3-5 times, until the water is completely clean and no black water, turn off the water supply power, the cartridge will be connected back to the original.