Training Experience Reflections

When we reflect and have new inspiration, record it in the experience to keep in mind, which can help us summarize our past thoughts, work and study. Do you want to think about how to write the experience? The following is my collection of practical training experience experience thoughts, only for reference, we take a look at it.

Training experience experience thoughts 1

After the school's efforts to make me have the opportunity to visit the factory, I cherish the opportunity to go to training and feel very happy, which not only reflects the school leadership on the importance of the students, but also reflects the leadership of the infinite care of the students, with excitement, followed by the teacher into the factory, first of all, walked into the company's conference room, the wall hung with a list of outstanding employees, rest and relaxation, and then the company's staff, and then the company's staff. The list of excellent employees, rest a moment, the Minister of Human Resources led us to visit the factory, the way through the logistics room, the general office, the general manager's office, the financial room, the R & D room, the network room, the purchasing room, the office of the Ministry of Production, the finished product storehouse, the production workshop and so on,

Which, we focus on the visit to the production workshop, the first to see is the mounting group to do is to weld the patch, which is entirely Pure manual work, the next step is to add power to check whether the patch is qualified, this process is called the process of inspection, plus the electricity is DC, and then see the room high-frequency power supply, high-frequency power supply is the role of the buck processing, followed by the transformer, the role of the transformer is the conversion of power, the workers wrapped by hand with the copper wire, the device should be placed in the high-temperature aging room and high and low-temperature test chamber for the environment, the temperature test, the procedures are all completed! After the completion of these processes, and then engraved with the company's logo, a finished product is born.

Every factory is not a simple process, are the theory of the practice of the book from the factory visit to my feelings, I must study hard in the future, pay attention to the practical ability, for the future of the career to lay a good foundation,

First, the purpose of the training

Through the production of factory visits and participation in the actual, the combination of theoretical knowledge and production practice. Combine theoretical knowledge and production practice, optimize the knowledge structure, improve the ability to think and analyze. In the process of visiting, through the technical staff to ask questions to learn, understand and preliminary grasp of the technical parameters of the products related to this specialty and other aspects of the actual knowledge and related standards, enhance the boiler, turbine system and auxiliary equipment composition and structure of the specific knowledge, for the future study of professional courses, professional course design and graduation design to lay a good foundation. In addition, after the field understanding of the power plant, for the future into the community to make the necessary psychological preparation.

Second, the content of the practical training

March 24th

Today is the first day to the x power plant, from the way to the x have a good impression. Clean ground, clean sky, in short, is the fresh feeling. x power plant is located in xx district, from the Bohai Bay is very close to the installed capacity of 4 sets of 300,000. The plant is clean and organized, and everywhere is filled with the new atmosphere of hard work. First came to Sapporo, the first to solve the problem of life, eating and drinking water is undoubtedly the most important, the most helpless is the x of the cafeteria at 6:00, and used to the school at 5:00 to eat us, more or less a little unprepared, had to bear the tummy growling, and in a hurry to find a new way to solve the problem. After a full meal, and began to do four years of entertainment. Everyone's mouth, more or less some of the complaints, the most is still on the practical training of the longing, as well as some of their hearts, longing for a good weekend to come soon ...

Familiarize yourself with the geography of the environment, is the first task of each of us to a new place. After the meal time, called on three or two students, began our x journey. x building is very characteristic, are unified yellow wall red tile shape, also make the living area looks orderly, staggered. The large plastic playground looks particularly attractive, to be able to play a game of soccer on the green lawn would be even better. Soccer field, basketball court...all kinds of facilities are readily available. More exciting is the culture and sports center, where employees can relax, billiards, ping-pong, KTV... What is available outside, we also have x, I can not help but yearn for x work. Behind the culture and sports center is the staff hospital, fully embodies the humanization of x. Unconsciously have been in x turn nearly an hour, x also have a preliminary understanding, I believe that this x trip will be harvested not small.

March 25th

Today is the second day of the x power plant, according to the arrangement, get up early, and as expected to eat the power plant cafeteria breakfast, feel pretty good, to be much better than the school. Under the leadership of Mr. Li, we came to the training center and started the official training schedule.

First of all, there is a power plant Yang, gave me a brief introduction to the safety regulations of the power plant. As an electricity student who has been to the power plant more than once, I know it absolutely well. However, Yang Gong's introduction is still very distinctive, a vivid example, let us remember, the expression is also unconsciously serious. In the following time, Mr. Yang gave a detailed introduction to the x power plant, which was started in 1978 and constructed in two phases, the first phase of which was the introduction of 2x300,000 oil-fired units from an Italian company, which was put into operation in 1980, which was very advanced at that time. It was very advanced at that time, and the control system was Bailey's 820 system. The second phase of the project, aiming to serve the Asian Games, started construction in 1990 with 2x300,000 coal-fired units, also imported from Italy. In the country, x power plant can be said in two ways. One is big, in the domestic power plant at that time, x with 1.3 million of total installed capacity in the country swings ahead, can be said to be the leader of the national power generation industry, and x in the level of equipment and operation and management level, are leaders in the power industry. The second is old, x from the start of construction to date, has accompanied the growth of new China, through 30 years of wind and rain, witnessed the brilliant development of new China, relative to the new construction of power plants, x can be said to be their learning 'role model and predecessor. With the changes in international oil prices, the two coal-fired units could no longer adapt to the new market environment and ceased operation in 20xx. With the approval of the North China Bureau at that time, x started the oil-to-coal conversion project in 20xx, converting the two oil-fired units in the first phase into coal-fired units. Unit 2 was converted and put into operation in 20xx, and Unit 1 was converted and put into operation at the end of 20xx. The Phase 1 FGD unit was retrofitted at the same time as the conversion of Unit 1. Now, the desulfurization unit of Phase II is also being installed. I believe that soon x will be built more beautiful.

Practical training experience experience feeling 2

Building construction practical training in the twinkling of an eye to the end, I feel very deep, although in the process of practical training encountered a lot of problems, but after our efforts and the teacher's help are successfully solved. This also makes me feel the importance of cooperation between a team and the truth that theory must be combined with practice. In this practical training, I came across a lot of things that I didn't know before, such as positioning, placing lines, etc. These are the things that I didn't know in my last summer practical training. These in my last summer training, although I have seen, but for various reasons have not been able to try, in this training, I finally participate in it, and students together from the most basic positioning, starting from the line, from the concrete pad to the foundation to the walls and columns, we have to do it, although the results are not very good, but we are more satisfied.

First of all, I would like to say that this practical training is a good opportunity for me to exercise, because I have experienced several practical training in the first two semesters of my freshman year, but this time is so different. It will test my ability in all aspects: study, life, psychology, body, mind and so on. It will test whether I can put the theoretical knowledge I have learned into practice, and it is also the key to building my confidence, so I am 100% committed to it! Two weeks of intense and full of practical training life is over, in these two weeks I still have a lot of harvest. It is necessary to summarize the end of practical training. Through two weeks of practical training and practice, I learned a lot of valuable practical experience. The so-called practice is the only standard for testing the truth, this practical training so that I have a close look at the civil engineering construction process, learned a lot of very applicable to the specific construction knowledge, this knowledge is often in the classroom I rarely contact, rarely pay attention to, but is very important basic knowledge. The following is my summary at the end of the above multiple processes.

First, the purpose of training and requirements

1, can read and understand the general engineering civil construction drawings, and practical hands-on mastery of the main construction process of the sub-projects;

2, to understand the sub-projects of the various types of construction processes and characteristics;

3, familiar with the civil engineering often equipped with the construction machinery Types and their uses;

4, master construction quality inspection and acceptance procedures.

Second, the content of the training and attention

(a) the basic content:

1, first of all, the use of learned knowledge to familiarize themselves with the training construction drawings;

2, sub-parts of the project (masonry, reinforcing steel, template works, scaffolding works, etc.) of the main construction process in the construction of the practical training In the process of gradual mastery;

3, in the process of construction training should always pay attention to the construction process and characteristics of the major individual projects;

4, familiar with the construction equipment and machinery, construction quality inspection, on-site quality inspection of materials and construction, and so on.

(B) Note:

1, the practical training location for the school training center.

2, all actions should be subject to know the teacher's command, no unauthorized action;

3, strictly abide by the safety discipline, to ensure the personal safety of individuals;

4, into the scene must bring a helmet, not wearing skirts, shorts, slippers, sandals into the construction site;

5, during the training period shall not be unauthorized to leave the post, there are things that must be to instructor Leave;

6, practical training during the regular contact with the instructor, report the progress of practical training.

7, such as the violation of the operating procedures, all the problems, the consequences.

Third, the content of practical training and experience

Content:

(a) Reinforcing steel works:

1), the foundation base plate and the foundation beam reinforcement binding:

1, according to the popping out of the location of the steel line, the first pavement of the lower layer of the base plate reinforcing steel. According to the bottom plate stress situation, decide which direction of the lower layer of steel reinforcement steel below, in general, first paved short to the steel, and then paved long to the steel.

2, placed on the bottom of the concrete protective layer with mortar pads, pad thickness is equal to the thickness of the protective layer, according to the distance of every 1m or so can be narrowed, and even mortar pads can be replaced with iron instead.

3, the base plate, such as foundation beams, can be tied in sections of molding, and then installed in place, or according to the beam location line tied in place molding.

4, the base plate reinforcement such as tied joints, reinforcement lap length and lap position should be in accordance with the requirements of the construction specification, reinforcement lap should be wire in the center and the ends of the tie. If welded joints, in addition to welding regulations should be taken in accordance with the provisions of the specimen, the location of the joint should also comply with the provisions of the construction specification.

5, according to the pop-up walls, columns location line, the walls, columns into the foundation of the insertion bars tied firmly, inserted into the foundation depth to meet the design requirements, the length of the dumping should not be too long, and the upper end of the measures should be taken to ensure that the dumping of the bar is vertical, not skewed, tilted, dislocated.

6. The first hoop at the beam end should be set at 50㎜ from the edge of column node. The hoop reinforcement at the intersection of beam end and column should be encrypted to meet the design requirements.

7. Lap joint of beam reinforcement: when the diameter of beam reinforcement is equal to or greater than 22mm, welded joints are preferred, and when it is less than 22mm, tied joints can be used, and the lap length should be in accordance with the provisions of the specification. The distance between the end of the lap length and the bend of the reinforcement shall not be less than 10 times of the diameter of the reinforcement. The joint should not be located in the maximum bending moment of the member, and the end of the ligated joint of grade Ⅰ reinforcement in the tensile region should be done with a curved hook (grade Ⅱ reinforcement can not be done with a curved hook), and the lap should be firmly tied at the center and both ends.

2), plate reinforcement binding

1, clean up the template above the debris, with chalk on the template to mark the main bar, distribution bar spacing.

2, according to the spacing of the good, first put the force reinforcement, after the distribution of tendons. Pre-embedded parts, electrical conduits, pre-drilled holes, etc. in time with the installation. Bidirectional stressed plate, short direction reinforcement in the lower, long direction reinforcement in the upper.

3. When there is a plate with beam in the cast-in-place slab, the plate with beam reinforcement should be tied first, and then the plate reinforcement should be placed.

4, in the reinforcing steel below the good mortar pad, spacing 1, 5 m. The thickness of the pad is equal to the thickness of the protective layer, should meet the design requirements, such as the design does not require, the plate thickness of the protective layer should be 15mm, the length of reinforcement laps and laps the same position as the beam requirements described earlier.

(ii) masonry works:

1, according to the requirements of practical training, do a good job of placing lines.

2, after the foundation is cleared, play a good axis, side lines, and other dimensions of the location line on the foundation as required, and double-check.

3, bricks should be stacked according to the required number of masonry parts near the masonry, according to different specifications of classification, stacking, stacking, in order to prepare for use.

4, good masonry preparation, preparation of two-wheeled carts to minimize manual handling of heavy physical labor, in order to improve work efficiency.

5, masonry mortar should be based on the design requirements and the actual materials on site

6, masonry brick wall should be based on the center line of the foundation to put out the wall inside and outside the edge line, hanging line, skin lying masonry. Masonry method using the Trinity masonry method. With bricks, the first corner masonry, junction and doorway, and then to the center masonry. Before masonry should be first test swing, so that the size of the brick with a large surface flat face down, the exposed surface should be flush diagonal mouth facing inward, one by one lying masonry sitting mortar, so that the mortar is full. Larger gaps between the bricks should be filled with small stones first after grouting practice. The width of the mortar joints is generally controlled at about 5 to 6 millimeters, paving gray thickness of 40 to 50 millimeters.

7, masonry, brick upper and lower skin should be staggered with each other, inside and outside the staggered lap masonry, to avoid the emergence of heavy seams, flat seams, empty seams and holes, at the same time, should pay attention to the reasonable placement of bricks should not be a knife-edge type, split type, bridge type, manger type, sandwich type, pairs of masonry type, layered type masonry to avoid the occurrence of mismatches after the masonry bearing the weight, cracking, drums and other phenomena.

1, production requirements

(1) shaped combination of steel moldboard: length 600, 750, 900, 1200, 1500mm, width 100,

150, 200, 250, 300mm.

(2) bamboo mat board, poplar board

(3) Connectors: U-clip, cross fastener, disk fastener, tie bolt.

(4) Clamps: column hoops, shaped hollow steel flutes, steel pipe struts, steel diagonal braces, steel trusses, beam brackets and so on.

(5) Steel mold plates and accessories should meet quality standards after repair.

(6) Isolating agent: special isolating agent.

2, the main machine tools

Circular saw, board hand, wire hammer, tape measure, crowbar, etc..

Prefabrication assembly: (1) assembly site should be compacted and leveled, conditions permit should be set up assembly operation platform.

(2) according to the template design drawing for assembly, each hole of the two adjacent boards should be tightened with a U-shaped card card, the keel with hook bolts outside the pad disc-shaped fasteners and flat plate side rib holes card tight.

(4) put the axis, template edge line, horizontal control elevation, the bottom of the template should be made cement mortar leveling layer, check and correct the column with the ground anchor has been buried

2, installation procedures: 1) column demolding in the concrete after popping out the axis and horizontal line.

2) Before installing the beam steel column (such as for the bottom ground must be tamped) under the pillar pad through the length of the scaffolding board. General beam strut with a single row, when the beam cross-section is large can be used double or multiple rows, the spacing of the pillar should be designed by the template, in general, the spacing to 60 ~ 100 cm is appropriate. Above the pillar pad 10 × 10 cm square wood, pillar plus shear brace and horizontal tie rod. Off the ground 50 centimeters to set up a, above every 2 meters to set up a.

3) Adjust the elevation of the pillar according to the design elevation, and then install the beam floor, and straighten the line, the beam floor should be arched, when the beam span is equal to and greater than 4 meters, the beam floor according to the design requirements of the arch. If the design does not require, the arch height should be 1/1000 ~ 3/1000.

4) Tie the beam reinforcement, after checking and passing the hidden inspection, and remove debris, install the side templates, the two sides of the template and the base plate with a U-type card connection.

5) Fix the beam side template with beam bracket or tripod support. The keel spacing should be specified by the template design, generally appropriate for 75 cm, the beam template is fixed with a shaped card at the top of the template. When the beam height exceeds 60 centimeters, plus through the beam bolt reinforcement.

6) After installation, correct the beam centerline, elevation, section size. The beam template will be cleaned up debris, check and pass the pre-inspection.

(D) scaffolding project

1, fastener steel pipe scaffolding used as template support, the construction of its pole should meet the following requirements:

(1) support pole should be set vertically, 2m height of the vertical deviation is allowed to be 15mm.

(2) in the support of the pole at the root of the adjustable base, when the length of its extension exceeds 300mm, it should be fixed with reliable measures. Reliable measures should be taken to fix it.

(3) The bottom of each pole should be set up base or pad.

(4) Scaffolding bottom step should not be more than 2m.

(5) Scaffolding must be set up longitudinal and transversal sweeping rod also used right angle fasteners fixed on the vertical sweeping rod immediately below the vertical rod. When the base of the vertical pole is not at the same height, the vertical sweep pole must be extended two spans and fixed with the vertical pole, and the height difference should not be more than 1 m. The distance from the axis of the vertical pole to the slope should not be more than 500 mm.

(6) In addition to the top step of the top layer can be used to lap, the rest of the layers of the step joints must be used to docking fasteners connection. Butt, lap should meet the following requirements: butt fasteners on the vertical pole should be staggered, two adjacent vertical pole joints should not be set in synchronization, synchronization within the two joints in the height direction of the next vertical pole staggered distance should not be less than 500mm; the center of the joints to the main node should not be greater than the distance between the steps of the 1/3; lap length should not be less than 1m, y should be used for not less than 1m, should use not less than 2 rotating fasteners should be fixed, and the distance from the edge of the end fastener cover to the end of the pole should not be less than 100mm.

2, fastener steel pipe scaffolding is used as a full-tower template bracket, and its support should be set up in accordance with the following requirements:

(1)The template bracket higher than 4m, the ends and the center of every four rows of bracket poles should be set up with horizontal scissor braces every two steps from the top floor down.

(2) The four sides of the full template bracket and the middle of every four rows of bracket poles should be set up a vertical scissor braces, from the bottom to the top of the connecting settings.

(3) The setting of scissor braces should meet the requirements.

(E) plastering works:

1, process

a, wall cleaning b, watering sufficiently wet c, hanging vertical d, find square e, make ash cake f , grass-roots level treatment g, wipe the bottom layer of gray h, wipe the middle layer of gray

2, grass-roots level cleanup

(1) Brick masonry: the surface should be cleared of debris, residual mortar, tongue ash, dust and so on.

(2) concrete substrate: surface chiseling or wetting the surface after sprinkling water to brush 1:1 cement mortar (plus appropriate amount of adhesive or interfacial agent)

(3) in the concrete structure and masonry joints to set up reinforcing measures, the use of alkali-resistant fiberglass mesh cloth at the joints, laying width of not less than 10cm on each side, fixed directly to the wall surface with plastering mortar.

3, watering wet

Generally in the day before plastering, with a hose or rubber hose or spray bottle down the wall from top to bottom watering wet, it is appropriate to water twice a day.

4, hanging vertical, set square, looking for rules, do gray cake

According to the quality of plastering required by the training, according to the grass-roots surface leveling vertical situation, with the gray cake, and then wipe down the gray cake. When plastering the cake should be based on indoor plastering

Gray requirements + determine the correct location of the cake, and then use the ruler board to find a good vertical and level. The gray cake should be used 1:3 cement mortar plastered into a 5cm square wall as a reference, hanging vertical, set square, find rules to determine the thickness of plaster, plaster thickness should not be less than 7mm.

When the wall concavity is large should be lined in layers. The thickness of each layer should not be more than 7~9mm, and the operation should be wiped on the first. When the room area is large, the cross center line should be popped up on the ground first, and then pop up the wall corner line according to the level of the grass-roots surface, and then hang a plumb line and pop up the plumb line at 100mm from the corner of the wall, and then pop up the wall corner line according to the wall flipping lead pop up the wall thickness control line of the wall plastering layer on the two walls of the corner, so as to do the cake, and then according to the cake to fill the reinforcement.

5, do the corner

Walls, columns between the sun angle should be in the walls, columns before plastering with 1:2 cement mortar to do the corner, the height of the ground from the above 2 m. Then the walls, columns, the sun angle of the watering wet. The first step in the anodized corners on the front of eight ruler, ruler protruding from the side of the anodized corners, protruding from the thickness of the living plaster surface and flat. Then on the side of the corner, depending on the ruler side of cement mortar, and use the iron spatula to smooth it, according to the width of the corner (not less than 5cm) will be excess cement mortar shoveling. The second step is to wait for the cement mortar to dry a little, will be eight ruler to wipe the corner of the surface (eight slope to the outside). On the front side of the corner, wipe the cement mortar on the edge of the ruler and smooth it with an iron trowel, and remove the excess cement mortar according to the width of the corner. After wiping off the eight eight ruler, painted with cement paste to protect the sharp corners of the corner, and run the angle from top to bottom with a run through, so that the formation of obtuse corners.

Experience:

1) to do not know how to ask more, encountered do not understand, after their own thinking can not solve the problem, to be modest to teachers and students to ask for advice

2) to have perseverance and perseverance, construction learning is relatively speaking relatively boring, but the most basic knowledge of the building, so we must adhere to, can not be given up halfway.

3)Bricklaying seeks technology, to be careful, not sloppy, to do a good job.

4) Know how to cooperate with each other to improve construction efficiency.

Looking back on these two weeks of practical training, I think I need to mention the process, because it allows me to go from the classroom to practice, so that I know what I have learned is far from enough, some things in my training before that is a very simple thing, can be in the training are difficult to know where to start. Today's society construction industry in the national economic development and the construction of the four modernization plays a pivotal role, with the reform and opening-up policy of the implementation of the depth of the construction industry's role as a pillar is also increasingly being played. And as a construction of college students, we should learn the professional knowledge, and in practice to consolidate, and constantly innovate. In the classroom, and the teacher taught the basic theoretical knowledge to strengthen understanding and mastery, should also pay attention to the practice of exercises and skills training, the application of the knowledge of construction technology to solve some of the problems in the actual project, after this practical training, I have a deeper understanding of this course of architectural construction, so that I have a deeper understanding of the difference between the theory and practice. Let me learn a lot of construction experience that can not be learned in the classroom. As the saying goes: three ignorant cobblers are better than one. This is exactly the saying that unity is strength. During the practical training, the unity and cooperation is very important, especially in the construction process, the unity and cooperation is especially important practice. Practical training is the second classroom of university life, is the source of knowledge is always new and development, is the litmus test of the truth, is also an effective way for college students to exercise growth. Not only make me in the theory of construction technology in this field has a new understanding, but also in the practical ability to improve, and really make use of what I have learned. Under the careful guidance of teachers, I not only have a more practical understanding of construction technology, from the countless failures to learn valuable lessons, but also with the passage of time, their own will has been honed. I always remind myself that the only way to keep up with the times is to keep working hard.

At the same time, the instructor's help in the process of construction training is indispensable, here I would like to thank the instructor again, Mr. Zhao and Mr. Pu for their guidance and help in this practical training, in the future, I will be more diligent, and strive to have a more outstanding performance.

Practical training experience feeling 3

This is another year before the summer vacation short semester practical training! The main content of this practical training is financial software practical training. The main task of the training is to master the UFIDA erp-u8 financial software board theory of learning and its actual operation and use, while completing the daily training diary and complete the training report. The main place of practical training is the computer room of the School of Economics and Management, and the time of practical training is from July 12th to August 6th. Our lead teachers were Mr. X and Mr. X. Through the theoretical explanation and practical operation of Mr. X and Mr. X, we completed four weeks of practical training.

First, the purpose of practical training

In the current rapid development of the economy and business diversification and complexity of enterprises to intensify the situation, the actual needs of enterprises for accountants to do the level of accounting requirements are also increasing. The traditional manual accounting both time-consuming and labor-intensive and error-prone, can not meet the needs of enterprises. Therefore, in the unprecedented development of information technology today, the traditional accounting manual operation has been gradually replaced by computer. Computer operation that is, accounting computerization, which is mainly the application of electronic computers instead of manual bookkeeping, accounting, reporting, as well as replacing a part of our manually completed by the processing of accounting information, analysis and judgment of the process. It is a practical part of the theoretical study of financial accounting, financial management, computerized accounting, and an important part of our financial management and financial accounting majors to learn and improve the ability to use computers to deal with accounting processes. Through the study of practical courses, we have to basically master the actual enterprise accounts processing process, the basic principles of computerized accounting, the main functions and use of financial software, and be able to use financial software to carry out accounting processing of enterprise business. Through the study of computerization, we can lay a certain foundation for doing accounting work after graduation next year.

The main content of the practical training

(a) UFIDA financial software system management

financial software system management of this part, the main study of the system management of the relevant concepts, functions and basic settings. System management is UFIDA financial software (erp-u8) management system in a very special component. Its main function is to manage the various products of the software management system for the unified operation and maintenance of data, including account management, annual account management, centralized management of operators and permissions, management of system data and operational security.

(B) UFIDA financial software general ledger management

Through the experiment to master the general ledger management system concepts, functions and the relationship with other systems, set the control coefficients, set up the basic data, enter the opening balance and so on. The general ledger management system is the core system of financial and business management software, which is applicable to accounting and management in various industries. The main functions of general ledger management are: initial setup, voucher management, cashier management, account book management, auxiliary accounting management and month-end processing. The important position of general ledger management system cannot be ignored, other management such as: payroll management, fixed assets, accounts receivable and payable, fund management, cost management, inventory management, etc. are operating around the general ledger management. The last step of the general ledger management system is the end-of-period processing, which mainly includes bank reconciliation, automatic transfer, reconciliation, month-end processing and year-end processing. The number of manual accounting is not large, but the variety of business time is tight, and in the computer operation of many of the end of the period processing with regularity, not only to reduce the workload of the accounting staff and strengthen the standardization of financial accounting.

The main learning content is an overview of the ufo statement system, to understand the ufo statement and other systems of the main relationship, business processes. The ufo report management system of UFERP-u8 software is a tool for report transaction processing. He has a perfect interface with UFIDA accounts and other systems, with convenient customized report functions, data processing functions, built-in accounting reports commonly used in a number of industries; this system can be run independently for dealing with day-to-day office affairs. Report format definition, formula definition and report templates, report data processing, table page management, and report output and charting functions are ufo report management is the main operation of the processing content.