With the living conditions become better, people's requirements for headphones is also higher and higher, in addition to the appearance of good-looking, people began to pay attention to the sound quality of the headset, a good headset can present the most perfect sound quality, today Xiaobunny introduced to you is about the repair and maintenance of the Audio-Technica headphones, I believe that music enthusiasts of the Audio-Technica this brand will not be unfamiliar with this kind of headset is not only the sound quality of the great, but also very cool appearance. The appearance is also very cool Oh! The following is to say about the maintenance of Audio-Technica related content.
Technical Triangle headquarters was established in Japan in 1962, the company's global development team has been committed to the design, manufacture, marketing and distribution of audio equipment. From its initial focus on phonograph cartridge technology, Audio-Technica has been able to develop high-performance microphones, headphones, wireless systems, even commercial rice-ball forming machines, and other high-quality electronics for professionals and the general public.
Warranty Regulations:
The Company guarantees to the user that the products listed in this warranty card are in good working order and that the parts are complete, and provides free warranty service, the terms of the warranty are as follows:
1. Consumers from the date of purchase according to the product warranty card within the warranty period, the product quality failure, confirmed by the company's technical staff of the failure of the machine is under normal use, will provide free warranty service, but all replacement parts belong to the company.
2. In the following cases, we will refuse to provide free warranty service, but will provide repair service and charge the related parts and labor cost as appropriate:
a.? The product has been operated incorrectly, used negligently or damaged due to force majeure; b.? The product has been repaired without our authorization; c.? The headphone unit has been used at high volume, into the debris or impact caused by deformation of the diaphragm, headphone cable breakage, crushing, flooding, shell damage, deformation and other man-made damage; d.? The product does not operate according to the original installation instructions provided by the manufacturer; e.? Unable to provide the original warranty card related to the sales unit of the sales certificate, or the date of purchase beyond the warranty period.3.? We will refuse to provide repair service under the following circumstances:
a.? Can not provide the original warranty card or product warranty card recorded in the content does not match the product; b.? Warranty card, anti-counterfeiting label logistics code content has been altered, or blurred and can not be recognized.4. The free service provided by this warranty card does not include product accessories and other decorative items.
5. Warranty service does not include transportation costs and does not provide on-site service.
Audio-Technica repair address:
Beijing Chaoyang District, No. 2 Guanghua Road? Sunshine 100?D Block?602?room
Room 908, Hongrui Building, No.31 Zhongshan 2nd Road, Yuexiu District, Guangzhou City, Guangdong Province, China
310, 3F, No.244 Liaoning Road, Hongkou District, Shanghai, China
How to repair broken Audio-Technica headphones?
Membrane collapse, membrane cracking, membrane detachment, into the treatment of iron powder
General headphones have broken sound, murmurs, bass missing faults when the general consideration may be caused by the above reasons. First of all, open the headset shell, for the soft-set structure of the headset first removed the soft-set, and then pointed tweezers and other sharp tools a little pick open the iron mesh and steel cover, until the membrane is fully exposed. Hard shell headphones can first use a small flat head screwdriver in the joints with a circle, and then the general can be easily opened, and eventually make the membrane all exposed. Large headphones are another matter, in any case, to make the headset membrane all exposed, in order to facilitate the operation.
Membrane collapse, for the membrane collapse failure, the tweezers can be used to clip a small piece of double-sided adhesive, and gently lift the membrane collapsed place sticky. Pay attention to control the size of the strength. Membrane recovery can be installed back to the original.
The membrane is cracked, the possibility of repair is not great, even if the sound quality will be damaged. However, there are successful treatment, the degree of damage to the sound quality is very light, can be ignored. That is, use a needle dipped in a little 704 glue (also called vulcanized silicone), coated in the crack. Be careful not to be too thick, cover the cracks can be. Then install the shell. Remember not to immediately go to the audition, should be left for two days before trying. Because the vulcanized silica gel dries slowly.
The membrane is peeling off, use 704 or fish bead glue to apply a little, can be stuck. Pay attention to the sticky flat compression. Put it back and leave it for a day.
Into the iron powder, with a cotton swab dipped in water and then dabbed down the iron powder, and then deal with the membrane collapse.
Treatment of broken voice coil
If the headset is silent and the measurement wire is good. Measure the back of the unit does not conduct between the two solder joints. Then it is determined that the voice coil broken wire. Now the vast majority of earbuds are generally changed to lead from the side of the membrane, although this will have a slight impact on the sound quality, but it makes the lead wire vibration breakage possibility is greatly reduced. However, it is still often due to human factors to make the unit rotation will be rubbed off the line. To repair this, remove the membrane with a razor blade and pick up the voice coil wire with the tip of a needle. Separate the two wires and pull the wire out in the direction opposite to that of the winding direction, being very careful and noting that the two wires are in different directions. If you can't rip it out then don't pull it out with force, instead you should splice the tonearm wire long with a thin headphone cord. It is best to have a magnifying glass to assist you when diffusing the wire, you should tin the wire first, and then solder the wire with a pointed soldering iron. And use 704 adhesive to paste the wire on the headphone film. Then stick on the headphone film and solder the two voice coil wires leading out to the soldering points at the back. It's a good idea to protect the wires behind the torus with hot melt glue to prevent further rubbing off. Generally headphones with copper coils on top of the membrane will have a higher success rate of repair, and the impact on sound quality will be less.
All right! The above is about the Audio-Technica repair of all the introduction, a good brand not only product quality, after-sales service is also very good oh. With this cool headset out, the turnover rate must be very high it! Bunny also got an Audio-Technica headphones, big red very striking, this headset can be very good isolation outside the noisy sound, no matter where you can be immersed in their own music world, very awesome Oh!
Tuba Rabbit online free for everyone to provide "each decoration offer, 1-4 local decoration company, 3 sets of decoration design program", and decoration to avoid pit strategy! Click on this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, you can get free Oh~