The composition of the electric sliding door
The sliding door door is composed of a door frame (also known as cladding) and door panels. According to the sliding door door frame is divided into three kinds, one is aluminum alloy profile sliding door door frame (hereinafter referred to as aluminum alloy sliding door), the second is the stainless steel sliding door door frame (hereinafter referred to as stainless steel sliding door), and the third is the galvanized steel plate sliding door frame.
Electrical sliding door, its door body against the wind load requirements are more stringent, suitable for installation in a variety of plant building structure. This kind of door can be converted manually and electrically. Controllable door door number is not too much, generally single track. It is divided into two kinds of lower load-bearing and upper load-bearing.
Lower load-bearing: the door body is load-bearing by the bottom track, the top guide. Durable, minimal maintenance, simple security and control, adaptable to a variety of insulation and outer layer systems.
Top load-bearing: the weight of the door body is carried on the top, guided by the bottom. The upper part of the door body load-bearing track requires high strength, excellent load-bearing performance and high reliability of door body operation. Door body running friction is small, open light, smooth, door boot start torque requirements are small, small power consumption.
Electric sliding door control
1, control handle, wire control;
2, wireless remote control, common 433MHz wireless remote handle control;
3, external system control, such as electric door automatic release system through the embedded control system or computer control, the computer automatically recognizes the vehicle license plate, automatic door opening.
Electrical sliding door production method
Method 1: wire rope with the winch, simple installation, the middle section of the wire rope in the winch around a number of laps (the length of the winch position enough for you to the gate to the end of the more than two laps can be) wire rope ends were tied to the gate at the two ends of the lower corner of the track groove (the road needs to be a track groove), the hanging door tied to the upper end.
Method 2: chain with three-phase motor plus gearbox, chain installed on the ground for a number of meters (according to the height of the gearbox gear)
Electric sliding door price
As long as it is a commodity there must be a price. So what is the general price of motorized sliding doors sold by manufacturers? According to the electric sliding door products, in terms of design technology, as well as the design of the load, according to different requirements, are very different, as for the electric sliding door manufacturers sell price, generally wholesale prices, than the market is perhaps even lower. However, it is still important to pay attention to the quality of electric sliding door products and whether the switch is safe and stable. And electric sliding door brand is also more, generally speaking, about 800 yuan of electric sliding door is considered a mid-range products. If the electric sliding door manufacturers wholesale, then at least must need about 400 yuan! Electric sliding door installation
First step: first from the end of the header to remove the wooden box sealing a wooden bar, and then pull the door row from the wooden box.
The second step: after pulling out the header key to find, general header key are bundled in the end of the door row of cross-bar activities on the round tube with a bandage.
Third step: use the key to open the cover of the head of the motor next to the white box out, which has a wireless remote control * 2, wireless desk control * 1, clutch key * 1.
Fourth step: the role of the wireless remote control is to control the operation of the telescopic door with a small and exquisite easy to carry. The desk control is used to place in the guard room to facilitate the daily operation of the security personnel.
Step 5: If the use of remote control door operation when the "gears turn, the shaft does not work" situation, that the motor clutch is not closed. Insert the hexagonal clutch key in the box into the end of the shaft that binds the chain to the motor has a hexagonal groove that is recessed to the inside, insert the clutch key into it and turn it 180 degrees to open the clutch.
Sixth step: motor debugging good after the door row close against the wall (need to let the door body fixed position) in the end of the door body at the bottom of three fixed parts, the first is the door row in the middle of the horizontal row of square tube above a corner code, can be fixed on the wall. At the bottom of the end of the door row there is a horizontal row of square tubes with two stainless steel angle yards at the inner left and right ends, which can fix the door body on the ground (suitable for installation sites without wall pillars).
Seventh step: the door body closed against the wall to the center of the door body, subject to the left and right side of the wall side to side in the middle of the door row of parts along the straight line every 20 ~ 25 centimeters each buried a round magnet eighth step: buried after the round magnet in the door row when the door closes the head of the stopping parts of the square magnet buried directly below.
Step 8: After the door is fully extended, bury a square magnet directly below the head stopping part in the first 30~100mm from the head stop after the door is fully extended.
Part IX: At a distance of about 1000mm from the door and the wall, bury a square magnet at the bottom of the head (corresponding to the part of the white tube [infrared reed switch]) 150mn away from the round magnet (the middle part of the track).
Step 10: pass on the 220-volt power supply (two compartments of electricity 2.5 square) voltage can not be lower than 180 pay, three power lines correspond to the red (fire), yellow (ground), blue (zero). After connecting the three wires (ground can not be connected) can be completed!
Electric sliding door manufacturers recommended
1. Zhongshan City, Botou Electromechanical Technology Co., Ltd. production of trips to the door machine, gate machine, intelligent door opener, intelligent charging system using Italian technology with a high degree of intelligence, humanization, torque, small size, installation, easy to use, the product will be unanimously praised by domestic and foreign customers once the world has won. Address: No.10 Building, Shengping Middle Road, Xiaolan Town, Zhongshan City, China.
The company produces the advantages of electric sliding door: anti-strong wind obstruction, when the automatic door is in the process of closing, such as the outside world strong wind obstruction of the door, the control system will carry out automatic power correction, improve the motor torque, forcing the door to close.
2. Henan Mingrui Door Industry Co., Ltd. main products are: automatic door series: automatic induction door, automatic sliding door; revolving door series: two-winged revolving door, three-winged automatic revolving door, three-winged manual revolving door, retractable door series: garage door, automatic access control system. The company has established an after-sales service system aiming at customer satisfaction to ensure product quality and meet customer requirements. Address: No. 61-03, Area C, Tianrong International Building Materials Port, Zhengzhou, China.
The company's electric sliding door with standard configuration can be connected to a variety of additional accessories, suitable for a variety of occasions and environments, PU guide wheel design, so that the door running more quiet and smooth.
3. Henan Yinfeng Financial Equipment Co., Ltd. formerly known as Zhengzhou City People's Bank Equipment Factory 1993 restructured into Henan Yinfeng Financial Equipment Co., Ltd. is a comprehensive enterprise with a history of more than 30 years set of financial equipment (equipment) research and development, production, sales and after-sales service as a whole.
The company's production of electric sliding doors open flexible, large span, light weight, no noise, sound insulation, heat preservation, strong wind resistance, easy to operate, smooth operation, not easy to damage.