1. Stop error number: 0x0000000a
Interpretation text rql- not less than or equal to
Common cause: The driver used an incorrect memory address.
Solution: If you can't log in, restart the computer. When the list of available operating systems appears, press f8. On the windows Advanced Options menu screen, select Last Known Configuration and press Enter.
Check whether all new hardware or software is installed correctly. If this is a new installation, please contact the manufacturer of hardware or software to obtain any windows updates or drivers that may be needed.
Run all the system diagnostic software provided by the computer manufacturer, especially the memory check.
Disable or uninstall newly installed hardware (memory, adapter, hard disk, modem, etc.). ), driver or software.
Ensure that hardware device drivers and system bios are up to date.
Make sure that the manufacturer can help you get the latest version and get these hardware.
Disable bios memory options such as caching or shadowing.
2. Stop error number: 0x0000001e.
Description: kmode- extended-unprocessed
Common cause: Kernel mode process tries to execute illegal or unknown processor instructions.
Solution: Make sure there is enough space, especially when performing a new installation.
If the stop error message indicates a specific driver, disable it. If you can't start the computer, you should try to start it in safe mode to remove or disable the driver.
If there is a video driver that microsoft does not support, try switching to a standard vga driver or an appropriate driver provided by windows.
Disable all newly installed drivers.
Make sure you have the latest version of the system bios. Hardware manufacturers can help you determine whether you have the latest version or get the latest version.
Bios memory options, such as cache, shadow.
3. Stop error number: 0x00000023 or 0x0000024.
Description: fat file system or mtfs file system.
Common cause: The problem occurs in ntfs.sys (a driver file that allows the system to read and write ntfs drives).
Solution: Run the system diagnostic software provided by the computer manufacturer, especially the hardware diagnostic software. ..
Disable or uninstall all antivirus software, disk defragmenter or backup programs.
Run the chkdsk /f command at the command prompt, check whether the hard drive is damaged, and then restart the computer.
4. Stop number: 0x0000002e
Description text ATA- Bus-Error
Common causes: system memory parity error, usually caused by hardware problems.
Solution: Remove all newly installed hardware (memory, adapter, hard disk, modem, etc.).
Run system diagnostic software provided by computer manufacturers, especially hardware diagnostic software.
Ensure that hardware device drivers and system bios are up to date.
Using the system diagnostics provided by the hardware vendor, run a memory check to find faulty or mismatched memory.
Disable bios memory options such as caching or shadowing.
When the list of available systems appears after startup, press f8. On the windows Advanced Options menu screen, select Start vga Mode:. Then press Enter. If this does not solve the problem, you may need to change a different video adapter list. For a list of supported video adapters, refer to the hardware compatibility list.
5. Stop number: 0x0000003f
Description: no mor- system -ptes
The usual reason: clean the driver correctly every time.
Solution: Disable or uninstall all antivirus software, disk defragmenter or backup programs.
6: Stop error number: 0x00000058
Description: ftdisk-internet- error
Common cause: A primary drive in a fault-tolerant set has failed.
Solution: Start the computer with the windows installation disk and boot from the mirrored (second) system drive. For instructions on how to edit the boot.ini file to point to the mirror system drive, you can search for "editarc path" on the microsoft Support Services website.
7. Stop error number: 0x0000007b
Description text n can access the boot device.
Common reasons: i/o system (usually refers to boot device or file system) failed to initialize.
Solution: Boot sector viruses usually cause this stop error. Use the latest version of antivirus software to check the computer for viruses. If a virus is found, it must be deleted from the computer through necessary search. Refer to the antivirus software documentation to learn how to perform these steps.
Remove all newly installed hardware (memory, adapters, modems, etc.). ).
Check the microsoft hardware compatibility list to ensure that all hardware and drivers are compatible with windows.
If you use scsi adapters, you can get the latest windows drivers from hardware manufacturers, disable synchronization negotiation of scsi devices, check whether the scsi chain is terminated, and check the scsiid of these devices. If you are not sure how to perform these steps, you can refer to the documentation of your hardware device.
If you are using an ide device, please define the ide port on the motherboard as the only main port. Check the master/slave/unique settings of the ide device. Remove all ide devices except the hard disk. If you are not sure how to do this, please refer to the hardware documentation.
If the computer has been formatted with ntfs file system, you can restart the computer and then run the chkdsk/f/r command on the system partition. If the system fails to start due to an error, please use the command console and run the chkdsk /r command.
Run chkdsk /f command to determine whether the file system is damaged. If windows cannot run the chkdsk command, move the drive to another computer running windows, and then run the chkdsk command from this computer.
8. Stop error number: 0x0000007f
Description: Unexpected kernel mode trap
Common causes: usually caused by hardware or software problems, but usually caused by hardware failure. ..
Solution: Check the microsoft hardware compatibility list to ensure that all hardware and drivers are compatible with windows. This problem will occur if the computer motherboard is incompatible.
Remove the newly installed hardware.
Run all the system diagnostic software provided by the computer manufacturer, especially the memory check.
Disable bios memory options such as caching or shadowing.
9. Stop error number: 0x00000050
Describe Text Age-Error in Non-Page Area
Common causes: memory error (unable to exchange data to disk using paging file).
Solution: Remove all newly installed hardware.
Run all the system diagnostic software provided by the computer manufacturer, especially the memory check.
Check whether all new hardware or software is installed correctly. If this is a new installation, please contact the hardware or software manufacturer to obtain any windows updates or drivers that may be needed.
Disable or uninstall all antivirus programs.
Disable bios memory options such as caching or shadowing.
10. Stop error number: 0x0000007
Description: Kernel stack page error
The usual reason is that the pages needed for kernel data cannot be read into memory from the paging file.
Solution: Use the latest version of antivirus software to check whether the computer has viruses. If you find a virus, please take the necessary steps to delete it from your computer. Please refer to all the system diagnostic software provided by the manufacturer, especially the memory check.
Disable bios memory options, such as caching and shadows.
1 1. Stop error number: 0x00000079.
Caption: Unmatched Hal
Common reasons: the hardware abstraction layer does not match the kernel or machine type (usually the configuration files of single processor and multi-processor are mixed in the same system).
Solution: To solve this error, you can use the command console to replace the wrong system file on your computer.
The kernel file of a single processor system is ntoskml.exe, while the kernel file of a multiprocessor system is ntkrnlmp.exe. However, these files should correspond to the files on the installation media. After installing windows2000 and Windows 2000, no matter which original file is used, it will be renamed as ntoskrnl.exe file. Hal files also use the name hal.dll after installation, but there are several possible Hal files on the installation media.
12. Stop error number: 0x0000007a
Description: Kernel data page error
The usual reason is that the pages needed for kernel data cannot be read into memory from the paging file. (usually caused by page file failure, virus, disk controller error or ram failure).
Solution: Use the latest version of antivirus software to check whether the computer has viruses. If you find the virus, then take necessary measures to remove it from the computer. Please refer to the software documentation of the disease degree to learn how to perform these steps.
If the computer has been formatted using the ntfs file system. You can restart your computer and then run the chkdsk/f/r command on the system partition. If the command cannot be started due to an error, please use the command console and run the chkdsk /r command.
Run all the system software provided by the computer manufacturer, especially the memory check.
13. Stop error number: 0xc000021a.
Description: Status-System-Process-Termination
Common causes: User-mode subsystems, such as winlogon or Client Server Runtime Subsystem (csrss), have been damaged, so security can no longer be guaranteed.
Solution: Remove all newly installed hardware.
If you can't log in, please restart your computer. When the list of available operating systems appears, press f8. On the windows2000 Advanced Options menu screen, select Last Known Good Configuration. Then press conference.
Run the recovery desk and let the system fix any detected errors.
14. Stop error number: 0xc000022 1
Description: Status-Image -check isu7m- Mismatch
Common cause: The driver or system dll is damaged.
Solution: Run the recovery console and let the system fix any detected errors.
If an error occurs immediately after ram is added to the computer, it may be that the page file is damaged, or the new ram is faulty or incompatible. Delete pagefile.sys and restore the system to the original ram configuration.
Code stop error number: 0x000000x
The 0 operation completed successfully.
1 error function.
The system cannot find the specified file.
3 The system cannot find the specified path.
4 The system cannot open the file.
5 Access denied.
The 6 handle is invalid.
7 The storage control block is corrupted.
8 There is not enough storage area available to execute this command.
9 The storage control block address is invalid.
10 environment error.
1 1 An attempt was made to load the program in an incorrect format.
The 12 access code is invalid.
13 data is invalid.
14 does not have enough storage area to complete the operation.
15 The system could not find the specified drive.
16 Unable to delete directory.
17 The system cannot move files to other disk drives.
There are no other documents.
19 media write protection.
The system cannot find the specified device.
2 1 The equipment is not ready.
The command is not recognized by the device.
23 Data error (cyclic redundancy check).
The program issued a command, but the length of the command was wrong.
The drive cannot find the specified area or track on the disk.
Unable to access the specified disk or floppy disk.
The drive cannot find the requested sector.
The printer is out of paper.
The system cannot write to the specified device.
The system cannot read the specified device.
3 1 The equipment connected to the system cannot operate normally.
The file is being used by another process, so it cannot be accessed now.
Part of the file is locked by another process, so it cannot be accessed now.
The floppy disk in the drive is incorrect. Please insert %2 (tag serial number: %3) into drive% 1.
Too many files to open * * *.
38 has reached the end of the file.
The disk is full.
50 does not support this network request.
5 1 The remote computer cannot be used.
There are duplicate names in the network.
The network path could not be found.
The network is busy.
The specified network resource or device is no longer available.
56 has reached the limit of network bios command.
An error occurred in the network adapter.
The specified server cannot perform the requested operation.
An unexpected error occurred in the network.
60 The remote adapter is not compatible.
6 1 The printer queue is full.
There is no space on the server to store files waiting to be printed.
The file waiting for printing has been deleted.
The specified network name cannot be used.
Access to the network is denied.
Network resource type is wrong.
The network name was not found.
68 has exceeded the name limit of the local computer network adapter card.
69 has exceeded the limit of network bios session.
The remote server has been suspended or is starting.
7 1 You can't connect to this remote computer at this time because the number of connections to this computer has reached the maximum.
The specified printer or disk device has been paused.
File exists.
Unable to create directory or file.
83 int 24 failed.
The storage area for processing this request is not available.
The local device name is in use.
The specified network password is incorrect.
87 parameter error.
There is a writing error on the network.
The system cannot start other processes at this time.
100 Unable to create other system flags.
10 1 is a special symbol belonging to other processes.
The 102 flag has been set and cannot be closed.
103 The flag cannot be set again.
104 cannot request a dedicated flag when it is interrupted.
105 The original ownership of this sign has been terminated.
Please insert a floppy disk into drive% 1.
107 The subsequent floppy disk was not inserted, and the program stopped.
108 The disk is in use or locked by another process.
109 pipeline has ended.
1 10 The system cannot open the specified device or file.
The file name of11is too long.
1 12 is out of disk space.
1 13 has no other internal file identifier available.
1 14 The target internal file identifier is incorrect.
1 17 The ioctl call run by this application is incorrect.
1 18 Confirm that the written switch parameter value is incorrect.
1 19 The requested command is not supported by the system.
120 This function is not supported by this system.
The 12 1 flag has timed out.
122 The data area passed to the system call is too small.
123 There is a syntax error in the file name, directory name or volume label.
124 The system call layer is incorrect.
125 disk has no volume label.
126 The specified module could not be found.
127 The specified procedure could not be found.
128 There is no subprocess to wait.
129% 1 The application cannot run in win32 mode.
130 attempted to operate with the file handle of the open disk partition (instead of the original disk i/o).
13 1 An attempt was made to move the file pointer before the beginning of the file.
132 Unable to set the file pointer in the specified device or file.
133 For drives that contain connected drives, you cannot use the join or subst command.
134 attempted to use the join or subst command on a connected drive.
135 attempted to use the join or subst command on a replaced drive.
136 The system tried to delete the connection of the unconnected drive.
137 The system tried to delete the replacement of the drive that has not been replaced.
138 The system tried to connect the drive to a directory under the connected drive.
139 The system tried to replace the drive with the directory under the replacement drive.
140 The system tried to connect the drive to the directory of the replaced drive.
14 1 The system tried to replace the drive with the directory under the connected drive.
142 at this time, the system cannot run join or subst.
143 The system cannot connect or replace a drive using a directory under the same drive.
144 This directory is not a subdirectory of the root directory.
145 directory is not empty.
The path specified by 146 has already been used in the replacement.
147 There are not enough resources to execute this command.
148 The specified path cannot be used at this time.
149 tried to connect to or replace the drive directory, and the directory on the drive was the target directory of the last replacement.
150 config.sys file does not specify system tracing information, or tracing is prohibited.
The number of specified signal events in 15 1 dosmuxsemwait is incorrect.
152 dosmuxsemwait is not running; Too many flags are set.
153 dosmuxsemwait list is incorrect.
154 The volume label entered exceeds the label character length limit of the target file system.
155 Unable to create another thread.
156 receives the process rejection signal.
157 has abandoned this area, so it cannot be locked.
The area has been unlocked.
159 The thread identifier address is wrong.
160 The parameter string passed to dosexecpgm is wrong.
The path specified by 16 1 is invalid.
162 signal has been suspended.
164 The system cannot create other threads.
167 Unable to lock the scope of the file.
170 The requested resource is in use.
173 The lock request is not important for the cancellation area provided.
174 file system does not support automatic change of lock type.
180 The system detected the wrong area code.
182 The operating system cannot run% 1.
183 Unable to create the existing file.
The flag sent by 186 is incorrect.
187 The specified system signal name could not be found.
188 The operating system cannot run% 1.
189 The operating system cannot run% 1.
190 The operating system cannot run% 1.
19 1 cannot run% 1 in win32 mode.
192 The operating system cannot run% 1.
193% 1 is not a valid win32 application.
194 The operating system cannot run% 1.
195 The operating system cannot run% 1.
196 The operating system cannot run this application.
197 At present, the operating system cannot be configured to run this application.
198 The operating system cannot run% 1.
199 The operating system cannot run this application.
200 code segments should be less than 64k.
20 1 The operating system cannot run% 1.
The operating system cannot run% 1.
The system cannot find the entered environment option.
Processes in the command subtree have no signal handles.
The file name or extension is too long.
207 Ring 2 stack is in use.
208 global file name characters * or? Incorrect, or the specified global file name contains too many characters.
The signal sent by 209 is incorrect.
2 10 cannot set the signal processor.
2 12 area is locked and cannot be reallocated.
2 14 There are too many dynamic link modules attached to this program or dynamic link module.
2 15 cannot call the nested loadmodule.
2 16 image file% 1 is valid, but it is not applicable to the native type.
The pipeline status is invalid.
23 1 All pipeline instances are busy.
Pipeline 232 is closing.
There is no process at the other end of the pipeline.
More data is available.
Session cancelled.
The specified extended property name is invalid.
255 Extended attributes are inconsistent.
258 Wait for the operation to expire.
No other data.
The copy function cannot be used.
The directory name is invalid.
The 275 extended attribute does not match the buffer.
276 The extended properties file on the mounted file system is corrupted.
The extended property sheet file is full.
The specified extended property handle is invalid.
The installed file system does not support extended attributes.
288 attempts to release the multi-channel synchronization signal that does not belong to the caller.
The 298 signal has been transmitted too many times.
299 only partially completed the readprocessmemory or writeprocessmemory request.
The 300 operation lock request was rejected.
30 1 The system received an invalid operation lock confirmation.
3 17 In the message file of %2, the system could not find the message text with message number 0x% 1.
487 attempted to access an invalid address.
The result of 534 operation exceeds 32 bits.
There is a process at the other end of the pipeline.
Wait for the process to open the other end of the pipeline.
994 Access to extended properties is denied.
995 i/o operation terminated abnormally due to thread exit or application requirements.
996 Overlapping i/o events are not in the marked state.
997 is processing overlapping i/o operations.
998 Invalid access to memory location.
999 An error occurred while performing an in-page operation.