A, air conditioning purification equipment which?
1, ozone sterilization borrowed ozone is the recent rise of sterilization methods. Ozone disinfection method is relatively simple to operate, will be connected to a car special disinfectant hose into the compartment, open the car special disinfectant and the car air conditioning, the use of air conditioning air circulation, the car special disinfectant produced by the high concentration of ozone sent to every corner of the car, only a few minutes, can be eliminated, the destruction of bacteria is more thorough, disinfection of the compartment will be retained a little bit of ozone smell, only need to open the windows a little while, the car windows. Ozone will automatically decompose into colorless and tasteless gas evaporated. However, this method needs to be sterilized once a month, the effect will be better.
2, the car oxygen bar car oxygen bar function is to increase the content of negative ions in the air, negative air ions have "air vitamins," said. Negative ions inhibit the growth of bacteria, viruses, remove air odors, clean air, the current market can be seen made into a variety of artistic modeling of the car with negative ion generators, that is, the car oxygen bar. But this method has an obvious drawback, although the increase in negative ions can make the driver awake, but can not remove the original pollutants in the air.
3, photocatalyst photocatalyst (Photocatalyst) is a nanoscale titanium dioxide (TiO2) as a representative of the photocatalytic function of the light semiconductor material
4, air freshener spray air freshener is a cure for the symptoms of the problem, the air freshener is not fresh, which itself may be the source of air pollution in the car. The so-called air freshener to get rid of pollution is only borrowed from the aroma of the aroma of a moment to cover people's sense of odor, can not be completely removed from the essence of harmful gases, so this is just a very inappropriate to use the method.
5, activated carbon adsorption filtration activated carbon is a kind of adsorbent, it has physical adsorption and chemical adsorption of double characteristics, can selectively adsorb a variety of harmful substances in the air, in order to achieve the purpose of detoxification and deodorization. Activated carbon should be replaced after adsorption saturation, about once every month. And this method in the space scope has great limitations, beyond its effective use of the scope of the loss of its role in air management. These are the advantages and disadvantages of some common air purification equipment on the market, I hope that after reading this article, you can according to their own needs to buy the right air purification equipment.
Two, purification air conditioning installation notes
1, dust ban. That is to say, the entire dust-free clean room is prohibited to have dust, but also expressly in how much range of airflow how much.
2, with dust. Prohibit personnel with dust into the dust-free clean room, any personnel into the dust-free clean room all can through the air shower room buffer channel blowing shower before entering. (The air shower room is one of the necessary equipment for employees to enter the clean room or dust-free workshop, it can minimize the staff in and out of the clean room brought about by the pollution problem, to enter the dust-free clean room workshop plays a big role.)
3, dust production. Prohibit dust production inside the dust-free clean room workshop, around the prohibition of dust dead-end blind zone, all using internal and external arc edging.
Three, no clean room purification air conditioning installation precautions:
A, purification air conditioning duct production should minimize the splicing, rectangular duct bottom width in 900mm or less, there should be no splicing, in the 900mm or more should minimize the longitudinal splicing, but there shall be no transverse splicing, 1000mm down to the lower limit of a splicing, 2400mm down to the lower limit of two splicing. Two splices below 2400mm, the splices bite a single flat bite, note that when making the bite will be spliced flat surface on the inner wall of the pipe, there shall be no anti-system phenomenon.
B, flexible flexible rectangular duct production using high-quality glossy artificial leather (or plastic-coated cloth), the production of the inner wall smooth, longitudinal seam gluing requirements for flat, no holes or leakage of glue gap.
C, purification of air conditioning duct and valve components produced in the form of bite day using a single flat bite, corner bite and joint corner bite, such as the use of snap bite must be coated with sealant, prohibit the use of mortise and tenon type connection, the corners of the duct and the four corners of the open hole need to be coated with sealant.
D, set up in the clean system air ducts on the inspection door, the production should be easy to open and close, good sealing, shall not be processed with black steel plate.
E, remove oil, storage in order to facilitate the cleaning and to avoid contamination of dirt, shall be set up 300mm above the ground platform, paved with δ of the cloth-clamped rubber sheet.
F, operation and installation personnel in the construction should wear clean, smooth, soft and non-dusty nurse hygiene clothing, into the clean room operation should change shoes, work gloves with white cloth gloves is appropriate.
I believe that we have a certain understanding of the air conditioning purification equipment through the above introduction, I hope you will be helpful, if there is anything else is not mentioned, please continue to pay attention.