Freezer coil installation details

Freezer coil installation details

Freezer coil installation details, the refrigerator is almost on everyone's home, one of the necessary furniture, how to install the coil in the freezer, this is a lot of people are not clear, different dual-temperature freezers, there are different ways to coil, I will share with you one of the next, on the installation of freezer coils details!

Maintain a constant low temperature of a refrigeration equipment, but also a food or other items to maintain a constant low temperature cold state of civilian products. Inside the box there is a compressor, ice machine for icing cabinets or boxes, with refrigeration device storage box. Domestic electric freezer volume is usually 20 ~ 500 liters. 1910 the world's first compression type refrigeration household refrigerator in the United States. 1925 Sweden Lido company developed a household absorption refrigerator. 1927 General Electric Company developed a fully enclosed refrigerator. 1930 years with different heating methods of air-cooled continuous diffusion absorption refrigerator on the market. 1931 year Developed a new refrigerant Freon 12.

freezer coil

freezer coil how to do - the main way of freezer coil: freezer coil way there are two main, one is the outer coil, the other is the inner coil, the outer coil is often able to The outer coil is often seen and understood, while the inner coil is not well understood. The freezer on the `plastic cover with a thin shovel pry open, after prying the aluminum skin, knocked open, and then the copper pipe in accordance with the way it is removed for the disk, and then use the adhesive to stick flat, through this way, the freezer coils all get good, so it's all done.

How to do the freezer coil - freezer coil installation: freezer horizontal coil is generally used with a diameter of 8mm copper pipe, from the mouth of the freezer 5-6cm at the disk of the first circle, and then circle by circle down the disk, each circle interval of 7cm from the bottom of the end of about 10cm. The upper part of the coil is connected to the capillary tube, and the bottom corner hole is opened to connect the compressor air intake. Coil to be flat, turn to be accurate, the length of the appropriate parts of the two ends of the aluminum card will be fixed in the inner wall of the freezer coil, the width of the card does not need to be fixed.

The freezer coil is very simple to say, do that is really who do who knows ah! As a crowd of melon eaters, we just need to understand the doorway is also, there is no need to have to do it yourself, after all, there are specialties. If you want to know more about how to do the freezer coil information, you can go to this system page to learn about the relevant knowledge.

The freezer coil installation details 2

The freezer plays a big role in the freezer is the freezer coil, and many people know very little about the freezer coil, the following we will introduce it in detail.

Steps to make the coil inside the freezer:

1, before dismantling the freezer to the freezer shell to mark, so that the recovery will not be wrong.

2, with a flat screwdriver and wrench with the upper frame from the inside pry open the freezer, along the upper frame of the freezer all around the need to pry loose.

3, after all the pry loose inside the upper frame, with a hammer and triangular steel along the outer edge of the upper frame of the freezer diagonal force percussion. Note that the hammer should not be smashed into the freezer box, otherwise the box will be smashed out of traces, affecting the appearance. After the outer frame is knocked loose all around, you can use a flat screwdriver to insert it, and slowly you can pry off the upper frame of the freezer. The upper frame has been removed.

4, with a steel ruler and flat iron and other tools to separate the aluminum skin. Separate the aluminum skin and insulation, do not rush, to prevent pulling the aluminum skin.

5, aluminum skin and insulation layer separate, do not rush to pump up the aluminum skin, to use a flat screwdriver to the bottom of the aluminum skin adhesion side of the aluminum skin tape cut to prevent the bottom of the aluminum skin pulled up, that is not good recovery.

6, you also need to use a flat screwdriver to loosen the slots in the bottom aluminum skin bit by bit. This will make it easy to pull out the aluminum skin, neither damage the side aluminum skin, nor pull out the bottom aluminum skin. Extracted complete aluminum skin. At this point the iron pipe inside is visible and rusty. The same rusty iron pipe in the cold room circle.

7, remove the original iron pipe. In the process of dismantling try not to destroy the insulation layer, there are buried deep in the insulation layer of the pipe with a razor blade and a flat screwdriver and other tools to dig out the insulation layer covering the pipeline, can not be pulled hard to prevent the whole piece of insulation layer to pull the separation off.

8, with the renovation of the new fish bead adhesive back and forth sticky aluminum skin, the aluminum skin to be glued back to the uniform brush on the fish bead adhesive. Freezer insulation also need to be evenly brushed on the fish bead adhesive.

9, brush the glue of the aluminum skin carefully inserted into the aluminum skin slots to stick well, with a hammer back and forth to knock, the aluminum skin sticky.

10, in order to smoothly install the upper frame, the upper frame of the original fixed aluminum slot inside the one with a flat FT screwdriver pry off, to prevent the upper frame can not be all the aluminum skin into the slot and the aluminum skin extrusion deformation. Installation of the frame, with a leather hammer on all sides of the solid. The appearance of the freezer is basically unchanged after installation.