2. Press the "Dehydration" function key to adjust the dehydration time as needed. Usually summer clothes can be done in one minute.
3. Turn the "Rinse" function key to turn off the rinsing times. (All the lights are out)
4. Press the "Wash" function key to turn off the washing time. (All the lights are out)
5. Press the "Start" button, wait for about one minute, and then start dehydration.
6. The washing mode and water level will not be set. Because the washing machine is different, the operation is slightly different.
The washing machine cannot be dehydrated.
Because most washing machines are powerful? Automatic washing machine? So dehydration is also an indispensable link in the whole washing process. If the washing machine can't dehydrate, first of all, it is necessary to analyze whether the clothes are put too much when washing. If you put too many clothes, washing, washing and dehydration will be unbalanced. Secondly, check whether the safety switch on the top cover of the washing machine is in good condition. Once the safety switch is damaged, the excellent brand power washing machine produced in Zhongshan can automatically sense and automatically cut off the top linkage switch. Finally, we have to consider whether the solenoid valve is damaged. In many powerful automatic washing machines, washing and dehydration are completed by shifting gears through solenoid valves. If the solenoid valve is damaged, dehydration naturally cannot be carried out.
Washing machine leaks
First of all, we have to seriously doubt whether the drain valve is too elastic or the drain line is too short, which makes the drain rubber ring unable to reach below. At this time, it is easy to cause cracks around the drain. We just need to reinstall the drain pipe.
Secondly, if it is due to external reasons such as cracks or scratches, we will go to a professional to replace the drain pipe.
Washing machine leaks
Under normal circumstances, the washing machine works under wet conditions. If the electrical components or lines inside the washing machine come into contact with water, it will have serious consequences. Therefore, if you find that the washing machine is a little sticky when washing clothes, don't continue to use it, and find a professional to check it immediately. If it is found that the liquid in the bucket is charged, we can basically judge that there is water leakage under the bucket, which is the problem of the impeller shaft.
Troubleshooting of washing machine unable to dehydrate
1. Clothes are in an unbalanced state during washing. Elimination method: you can put less clothes before washing, and don't stuff too much at once, so as not to cause imbalance when washing. The dehydration effect is not good.
2. The safety switch on the top cover of the washing machine is damaged. Try not to open the top cover during dehydration to avoid damaging the top linkage switch.
The drainage system of washing machine is blocked. Disassembly method: Remove the drain filter for cleaning, rinse the drain pipe with water, and remove the sundries in the drain valve.
4. The water level switch cannot be reset. Solution: Contact the after-sales point.
5. The washing machine can't be dehydrated due to motor failure. Troubleshooting: You can try to open the back cover of the washing machine and move the pulley by hand, if it is not stuck. After connecting the power supply, the motor? If there is buzzing and it doesn't rotate, the motor turns are short-circuited or damaged, or the capacitor is not connected to the motor circuit. At this point, cut off the power supply, remove the motor belt and restart. If the motor still does not rotate or the speed is low, it is a motor fault and should be repaired or replaced.
6. The damage of the solenoid valve causes the washing machine to be unable to dehydrate: the washing dehydration of the automatic washing machine is completed by changing the gear position at the bottom of the solenoid valve, and the damage of the solenoid valve will also make the dehydration unable to work normally!
7. The washing machine can't be dehydrated because the motor plug is loose. Elimination method: it should be plugged in again and tied with a tie line to prevent it from falling off again.
8. The washing machine can't be dehydrated due to the failure of the computer control panel: Troubleshooting: Only the brain control panel can be replaced, because its control panel is coated with glue to prevent water from entering, and the maintenance is quite inconvenient!
9. Because of the motor thermal protector, the washing machine will not dehydrate. Troubleshooting: The thermal protector cannot be used until it is reset.
10. Some models are not equipped with a dehydration key, so the washing machine will not dehydrate. Troubleshooting should first check whether the non-dehydration key is pressed. If this key is pressed, the washing machine will have anti-wrinkle function and will not dehydrate the clothes. As long as the non-dehydration key is released, the washing machine can be dehydrated.
Power washing machine official website:/
Weili washing machine maintenance Dian
Huayu Brother (Beijing) Electronic Technology Service Co., Ltd. (Chaoyang District Door-to-door Service)
Tel: 400-600-2564
Maintenance address: Heping Street/Zone KLOC-0/4/No.KLOC-0/8, Chaoyang District, Beijing.
Chengdu jinshide technology co., ltd,
Tel: 400-600-574 1
Maintenance address: No.80 Peifeng Road, Qingyang District, Chengdu/No.38, Building KLOC-0/6.
Taihu county Liangyou household appliances business department,
Tel: 152556926 1
Maintenance address: Hanlinyuan 1 Dong 1 No.201,Xincheng, Taihu County.
Jiecheng home appliance maintenance department,
Tel: 0552-2 1 13882.
Maintenance address: 20m west of Damuqiao, Guzhen County, Anhui Province.
Mingguang city Baiyun Household Appliances Maintenance Department,
Tel: 0550-8 157666
Maintenance address: No.494 Chihe Avenue, mingguang city, Chuzhou, Anhui.