I use formlabsform3+, the equipment is different, the order of operation is very different. Take desktop-level FDM for example: if you print offline, you usually copy the slice file to a memory card first, insert it into the machine and then turn it on. After powering on the machine, feed the filament and stop it after the filament is stabilized, then clean the printing platform and check the level. After finishing, you can select the file to print. After printing, clean the printing platform and exit the single filament; if you print on-line, turn on the machine first, and then operate the printer from the control interface to level and feed the filament. Then import the model file slicing, check the slicing finished directly print. The latter cleaning procedure is the same as 1.
What are the tips for using a 3D printer?
Adjusting the heat bed and nozzle: Flat bed and nozzle settings can improve the quality of 3D printing. To make it easier, you can use paper to determine the distance between the nozzle and the bed. The nozzle is clean and the paper stretches with the least resistance when it is not at the right distance from the bed. You can also return to the bottom of the nozzle without difficulty.
Nozzle too high
1: Consumables don't stick to the build surface
2: Filaments resemble spaghetti.
Nozzle too low
1: First layer is barely visible or too thin.
2: Gathering of consumables on the nozzle.
3: Heated bed cannot squeeze consumable material.
Check the nozzle temperature: too high a temperature can cause filaments to form between the parts. High temperatures can melt early layers that can cause deformities. To avoid this mistake, place a one-centimeter square on the other side of the building board, which leaves enough time for cooling. While adjusting the nozzle temperature, don't touch the nozzle, such as the AnycubicMegaPro, which has a nozzle temperature of around 200 degrees, which can cause scorching if touched.
Setting the optimal print temperature: It is important to adjust the temperature of the heat bed for best results as this can help with print adhesion. In AnycubicMegaPro print mode, each layer shrinks as it cools. Additionally, when the bed temperature is too high, the model may warp, and if you see this, you should lower the bed temperature slightly for your next print.
Storing supplies correctly: most supplies absorb water, including ABS, nylon, and flexible materials. It is important to keep them dry, so proper storage is very important. When a material gets wet, it expands when squeezed as the water turns to vapor and bubbles out of the plastic. If you look closely, it makes noise from the nozzle and creates smoke. Unfortunately, the biggest problem is that it creates a rough surface.
So store the plastic case with a desiccant between uses. Similarly, you can dry the wire by placing it in an oven at a very low temperature for a few hours.1. The first time you use a 3D printer you can perform maintenance and calibration. Ensure that the printer is in a state where it can print properly.
2. You need to draw the model you want to print, the model format should be stl format.
3. Upload the model, the general printer has a wireless transmission and U disk transmission in two ways. The model is sliced through the printer's supporting software, and then transferred to the printer.
4. Check whether the printer's printing material is sufficient, out of the material with the material is not a problem.
5. Check the printing platform of the printer, whether there is any problem. Whether the platform is flat, there is no foreign matter to interfere with the printing.
6. According to the printer to print the steps to print.
7. You can stay a little while, see the printer prints normally. You can leave. Problems immediately stop printing, so as to avoid subsequent cleanup problems trouble.
3D printer how to use, the software is difficult to use?
3D printer is not difficult to use, first you need to know what is a 3D model file, then you need to know how to use the layered coding software, and finally you need to know the 3D
printer control software. And you're ready to 3D print. Some 3D printers combine the last two steps together. It depends
on what control software your 3D printer uses.
The most common 3D model files are those with the stl suffix, which can be opened
with software such as 3DMAX, PROE, and MASTERCAM. Others use obj files.
Layered coding software commonly skeinforge, slic3r, Cura, kisslicer, etc.;
Control software:
Printrun, this software not only has the machine control function, but also with the slicing software integrated into one (let's say slic3r), so it can
to The entire process, from slicing to printing, can be done independently. It supports Mac, Linux, and PC platforms, and is available for almost all open source 3D printers
.
Repeteir-host, much like Printrun, is a comprehensive program with slicing, part positioning, and machine
control. Its user interface is more complex than Printrun's, but more intuitive. It also supports Mac, Linux, and PC operating platforms.
Pepeteir-Server
A relatively new Repeteir product. It works on a RaspberryPi (a credit-card-sized computer motherboard), can control multiple printers, consumes very little memory (only 5MB per printer), and has a relatively simple web interface. But Mac
and PC are not yet supported.
How does a 3D printer work?
The 3D printer connects to your computer and inputs the files you need to print.
You can go online to download the GCO format 3D files and then connected to the printer can be printed out can also use their own 3D modeling. Some are connected to the data line, some are inserted into the memory card, put the file inside the memory inserted into the machine on the OK. The operation panel is mostly in English, this you have to read the manual.
There is also the installation of consumables: first of all, the consumables tray installed in the 3d printer's main shell tray box, before installation, pay attention to observe the tray consumables are not tangled, knotted and so on bad situation. Cut the head of the consumables into the shape of the tip of the tower, in order to wear into the guide tube and feed motor hole. First, the consumables through the guide tube, and then from the motor hole out through, has been to the nozzle motor feed port. 3D printer nozzle heated to more than 200 degrees, the consumables through the feed port, and then tighten the adjusting screw knob.
3D printer use process and operation
Now on the market a large number of 3D printers, if the choice is good? Its use of the method and process and how is it? The following is my for you to organize 3D printer use process, I hope to help you.
3D printer use process
Before the printer prints the model items, first of all, it is recommended to check whether the power supply is connected and tight, whether the SD card is inserted or inserted correctly.
Adjust the overall settings of the printer, operate the software system in the printer, find the printable files in the SD card and click print. (Most of these friends who have used it know how to operate, there are just some not very well handled details need to pay attention to.)
Adjustment of the platform height
11, the printer nozzle horizontal position if lower than the platform to take over the horizontal position of the board, the nozzle is too low on the platform will cause great damage to the bottom plate or lead to the material can not be squeezed out of the clogging and lead to not normal printing. This requires the print operator to adjust the platform downward.
The horizontal position of the printer nozzle from the platform to accept the board level position is too high will lead to the printing of the extruded material can not properly stick to the bottom of the board, but also easily affected by the warping, thus affecting the quality of the printed products or lead to the inability to print. This requires the print operator to adjust the platform upward according to the situation.
According to the height of the distance between the printing platform and the nozzle, appropriate twisting of the printing platform to adjust the height of the platform to adjust the appropriate adjusting nut or click on the printer's own automatic leveling system to adjust the height of the platform; the current test experience, the optimal nozzle from the height of the platform for the thickness of a piece of A4 paper or for the height of 0.1mm.
Two, choose the best temperature
In do not know or are not sure of the best temperature of the existing wire printing, it is recommended that the temperature of the printer debugging, it is recommended that the magnitude of 3-5 ℃ to debug the best.
Such as the optimal temperature of a print wire in about 200 ℃. We have not determined the optimal printing temperature, at 180-190 ℃ can be 5 ℃ range debugging, to observe the nozzle discharge.
To debug the temperature close to 200 ° C when the range of 3 ° C or 2 ° C, such as debugging, observation of the nozzle material more smoothly until the record, you can get the best printing temperature.
Three, the nozzle plugging treatment method
Click the control panel button, select the "control" menu, click in and then select the "temperature" menu, click into the selection of "nozzle" menu, click and set the temperature (such as PLA material on the setting of 200 ℃), save; to be the nozzle to the set temperature value, press the spring machine arm, with the appropriate force will be the wire to the feed tube extrusion, until the nozzle of the filament outflow is normal, it can be used normally.
Click the control panel button, select the "control" menu, click in and then select the "temperature" menu, click into the selection of "nozzle "menu, click and set the temperature (such as PLA material on the setting of 200 ℃), save; to be heated to the set temperature value of the nozzle, press the spring machine arm, stay in the nozzle in all the wire pulled out, and then loaded into the new wire test, if the test is normal can be used normally.
Click the control panel button, select the "control" menu, click in and then select the "temperature" menu, click into the selection "nozzle "menu, click and set the temperature (such as PLA material on the setting of 200 ℃), save; unscrew the feed pipe connector and heat dissipation block, the use of through the head of the tool (such as a long, thin hexagonal screwdriver) will be in the nozzle of the residue of the nozzle hard to the direction of the nozzle to be extruded. If it can be extruded, connect the radiator and feeding device after extrusion, heat the nozzle to the set value, load the available wire test, the nozzle can be normal out of the wire can be used normally;
If you still can not be extruded, please remove the nozzle fittings, replacement of the nozzle or contact our after-sales service personnel.
Four, material material reasonable choice
The choice of material is mainly based on your printer is suitable for which material. Such as some specifically designed for the PLA, this type of printer in addition to printing PLA, generally can also print the PLA series such as wood lines and other parts of the print can also be printed such as TPU and other hard plastic class; and then some manufacturers specifically designed for the ABS to design the printer, in addition to ABS, HIPS and other materials can be printed. Specifically based on which type of material to design, it is best to ask the printer manufacturer.
Precautions:
1, do not touch the print platform during printing, which will directly affect the quality of prints.
2, after the completion of printing, do not touch the print nozzle when the temperature does not drop, so as to avoid scalding; in the absence of disconnecting the power supply do not touch the exposed wire, wire, wire boards and other energized equipment, so as to avoid electric shock.
Guess what you like:
1.Tsinghua senior entrepreneurial story
2.3d printing technology learning experience summary essay
3.3d printing technology learning experience
4.HP printer how to restore the factory settings of the method
5.3d printing technology in China thesis conclusion essay