1, industrial washing machine add about 40 liters of water, and then add 300 ml of chlorine bleach. The washing equipment is adjusted to a high water level, and when the water is filled up, add the bleach and stir well. After about twenty minutes, the chlorine bleach will have thoroughly cleaned off the dirt from the back of the inner drum of the industrial washing machine. After stirring and dewatering, the dirt will remain at the bottom of the inner drum of the washing equipment, which needs to be drained once more in order to drain the dirt completely.
2, the automatic washing machine is filled with water, and then add about 100 grams of baking soda dissolved in water, let the washing equipment running rolling 5 minutes, and leave it for two hours. Then the bottom of the automatic washing machine will discharge some dirt, and then use rice vinegar to soak the towel, into the washing equipment to let it idle for a period of time. Baking soda dissolved in water contains weak alkaline, has a certain cleaning, deodorizing effect, and can also soften the water, prevent the water calcium, magnesium ions to form insoluble soap scale, and decomposition of limescale and dirt has been formed. Rice vinegar also has the role of softening limescale and stains, the combination of the two will be able to achieve effective sterilization and decontamination effect.
3, the hotel washing equipment to the high water level, and then poured into the special cleaning agent. Let the equipment run for 5 minutes so that the detergent is fully dissolved, with the heating function of the industrial washing machine can be heated to about 40 degrees, and then turn off the power supply of the washing equipment, at least soak for more than 1 hour, and then wash according to the daily washing mode, after the completion of the washing can be seen in the equipment of the dirt floated to the surface of the water.
4, take down the drain of the washing equipment on an empty bucket, close the water inlet valve and the front door. Then the three kettle amount of water with descaling agent poured in an empty container, according to the ratio of l: 2 prepared and stirred well from the detergent additive box, press the power switch of the laundry equipment, let the washing drum rotate; to be descaling liquid from the drain pipe to the bucket, and then the discharge of descaling liquid from the detergent additive box to join, so repeated many times until the program runs out, open the filter to clean the filter. After the washing equipment is finished running, open the water inlet valve, the drain pipe back to its original position, and then re-select the washing program, and then run again, until the program is finished running again to clean the filter can be.
Two, what are the methods of industrial washing machine failure repair
Industrial laundry as a hotel hotel, factories, schools, institutions, laundries, laundries, washing plants and other washing equipment. Solve the problem of removing towels, fabrics, clothing and other dirt, freeing up the hands as well as improving work efficiency. In the production work, it is inevitable to encounter failure problems, so what are the methods of industrial washing machine failure repair?
1, Failure 1: usually washing machine carrying water below the standard water line, stop continue to automatically add water
Analysis and repair: this problem you need to consider the water pressure switch may have a problem, at this time the pressure inside the water chamber is small, resulting in the water pressure switch can not be automatically contacted to release the power supply point, which is the circuit is disconnected. Lead to stop the water supply. Adjust the water level switch to go in to the normal valve value so that it can contact the electrical contacts properly.
2, fault two: the water level exceeds the standard water line, any continue to supply water until the flow out of the washing machine
Water pressure switch circuit is short-circuited, you need to adjust the water pressure switch, so that it maintains access to the state, can be resolved. The repair of this fault requires some general knowledge of electricity. Leakage of water and electricity is one of the key points of industrial washing machine repair, involving personal safety, requires special attention.
3, fault three: industrial washing machine appeared serious water leakage phenomenon, which led to the occurrence of power leakage
The air guide tube blockage problem, or the air guide tube aging off the problem, which led to the gas can not be excluded, affecting the exclusion of water flow. Clean up the dirt in the air duct and make it clear. If you can't solve the problem, you need to replace it with a spare guide tube.
4, fault four: motor normal work, but the washing machine can not wash work
need to check the motor in the washing drum circuit connection problem, repair the circuit, or replace the damaged drum or motor. If the problem is the reducer, you need to replace the reducer immediately. Otherwise the washing machine will be completely paralyzed.
5, fault five: irregular rotation of the drum. And accompanied by the emission of abnormal sound
Consider the problem of the clutch of the dumping drum, which leads to the dislodgement of small items and affects the normal operation. Reinstall the parts on the clutch, such as the spring. When the clutch is damaged, it must be replaced immediately. Do not use parts that have been damaged.
6, fault six: motor positive, turbo reverse
This is caused by the deformation of the pawl fork, which is a small problem. But if you can not even solve the problem, it will lead to the washing machine completely scrapped. Adjust the screws to restore the pawl fork to its original shape. If the deformation is severe, it needs to be replaced.