One, motherboard installation
In the process of installation, some JS in order to save time and effort, often in the process of installing the motherboard only in the chassis of the fixed plate to install the 4-5 socket base, and then directly mounted on the motherboard, and in screwing the screws on the washer. This seems like it doesn't matter, but in fact there are very serious problems.
1, now many players in order to overclocking or mute the need to replace high-quality CPU, North and South Bridges, as well as graphics card coolers, and generally the weight of these coolers themselves is very heavy, if the motherboard base only on the 4 sleeve, then the force points at this time only around the motherboard, if it is a horizontal chassis may be better, but now most of the vertical chassis, the long term use of this motherboard! It is very easy to deform, serious or even cracked. At the same time, if only installed around the fixed base, in the installation of the graphics card, memory will be down to squeeze, it is also very easy to damage the motherboard.
2, the role of the motherboard fixed screw washers can not be small, you can prevent the screws directly in contact with the motherboard and chassis lead to the problem of short-circuit contact, while also shielding some of the motherboard and chassis chassis electrostatic as well as electromagnetic interference.
Second, all kinds of data lines, power lines, signal lines sorting and installation
Some installers in the installation of various types of connecting lines are often based on their own experience, closed eyes inserted (a bit exaggerated), which can easily lead to some of the chassis of the front equipment can not be used, the indicator light does not come on or some of the equipment can not run at high speed.
1, data cable connection. At present, many motherboard SATA interface is not all native, often only 1.2 is the native interface, in the installation of SATA devices, the data cable as far as possible to be inserted in the No. 1 and No. 2 port, which can maximize the performance of the SATA.
2, the front panel of the USB port, signal indicator, 1394 = = = is also very easy to ignore the part. Some players after the installation of the general only to see whether the machine can be lit, whether the system is running normally, and ignored these details. It is recommended that after the installation of the machine with a USB flash drive to try the front of the USB interface whether each can be used normally, hard disk indicator, power indicator are displayed normally.
3, chassis wiring. Some installers installed only two ends of a connection, installed after the chassis of a variety of power lines, data lines, signal lines intricate, some are directly in contact with the radiator, so the potential risk is very large, and now the hardware, especially the graphics card, CPU power consumption is very large, such as the 8800, the normal use of the temperature is 60-80 degrees, then a plastic connecting line and its consequences of prolonged contact! At the same time, the wiring is messy and the overall heat dissipation of the chassis is also an important hidden danger.
Three, chassis cooling and CPU cooling installation
First of all, it is recommended that we try to choose a larger size when purchasing a chassis, which is conducive to the cooling of the entire system. Secondly, the chassis cooling is mainly about an air duct, generally forward and back.
1, some players installed the purchase of the chassis does not come with a fan, and JS in order to save time installed generally will not take the initiative to recommend that you install a fan. In fact, do chassis duct is very necessary. First of all, can play a very good cooling effect, and secondly, can also effectively avoid dust deposition caused by a number of interface poor contact.
2, CPU cooling installation. Be sure to avoid the surface of the CPU and the bottom of the radiator is not completely contact, that is, the proverbial "false installation", after the installation, to pay attention to the bottom of the radiator and the CPU slot is parallel to whether the core is completely with the bottom of the radiator completely tight. The first thing you need to do is to apply the right amount of silicone, otherwise the heat conduction will turn into heat resistance.
Four, silent problem
In the installation store due to the environment is more noisy and relatively empty, the general noise of the machine is easy to be ignored, but when you hold home, especially in the dead of night, which noise ....... sometimes maddening! ~ So be sure to pay attention to the following details.
1, the choice of power supply. Power supply must choose silent power supply, that is, 12-inch or 14-inch fan power supply, which is silent a more critical issue. I used to Granite 400, the quality is nothing to say, but which sound ...... Of course, you can do it yourself DIY, but I think not everyone has the ability and time.
2, chassis fan and CPU cooler selection. This needless to say, the chassis fan selection 12-inch fan (recommended in the air inlet installed on the filter), CPU cooler if the hand is still wide open recommended not to use the original. Original fans are generally 3500-4000 rpm, which sound ......
3, the choice of chassis. This is the second mention of the chassis, so the chassis is actually a very important part of the computer machine. The choice of chassis is also very simple, first of all, the size of the best can be a little larger, can be installed before and after the 12-inch fan. Secondly, try to choose a brand chassis, such as Yongyang, Cooler, TT, etc. (this version of a chassis guide post, you can look at), a good chassis not only provides a good cooling environment, but also effectively avoid *** vibration problems.
4, everyone in the process of installing the machine according to their own needs to install fans, can not install as much as possible, such as the North and South Bridges, memory = = =, generally not overclocking players CPU fan + graphics card fan + chassis forward and backward out enough.
Five, test and "roast chicken"
"Hardware are installed, the system also G up, can light ........ The first thing you need to do is to get your computer up and running, and then you'll be able to get it to work. The computer can run normally for 1 hour does not mean that it can run for 10 hours. In addition, hard installing the system is also a good test for the hardware.
1, we installed the best time to bring a USB flash drive, copy some professional test software, mainly the monitor, CPU, memory, graphics card (this version of a special introduction to the test software post, here will not repeat).
2, after moving home, we must "roast chicken" (i.e., running continuously for 48 hours or more). At the same time, you can "roast chicken" during the uninterrupted testing of the hardware, such as 3Dmark continuous operation for several hours, SP2004 continuous operation for several hours, memtest continuous operation for a few hours, while commonly used software and games are a long time to run a test to see if there is a splash screen or blue screen situation! If there is a reason, it's best to find a replacement or return it to the store within a week.
These are a few problems that are easy to overlook in the process of saving a newbie, and one of the reasons why some inexplicable failures occur, and we must be careful when installing a computer. If you have some help, please help top it! Source: Digital Dynamic Connections Organizer