4. Boiler water quality management system
(1) Boiler water must be treated, and boilers with unqualified water quality are not allowed to be put into operation without reliable water treatment equipment.
(2) Strictly implement GB 1576-85 standard and strengthen water quality management.
(3) Boiler water treatment generally adopts chemical treatment outside the furnace. For vertical, horizontal, internal combustion and small hot water boilers, chemical treatment in the furnace can be used.
(4) For the boiler with dosing treatment in the furnace, the hardness of feed water, alkalinity of boiler water and PH value must be tested at least once per shift (dosing in feed water test tank).
(5) For boilers with chemical water treatment outside the furnace, the hardness, PH value and dissolved oxygen of the feed water shall be determined every 2 hours; The alkalinity, chlorine, PH and phosphate in boiler water should be measured every 2-4 hours.
(6) Full-time or part-time water quality laboratory technicians can only carry out water treatment after passing the examination by the labor department.
(7) For the operation of the ion exchanger, the operating procedures should be formulated according to the characteristics of the equipment and seriously implemented.
(8) Water treatment personnel should be familiar with and master the performance, properties and usage of equipment, instruments and chemicals.
(9) Reagents for analysis and testing shall be properly kept, and inflammable, explosive, toxic and harmful reagents shall be kept and used in strict accordance with regulations.
(10) When the boiler is shut down for maintenance, the water treatment personnel should first check the scale corrosion, and record the scale composition, thickness, corrosion area, depth and location in detail.
(1 1) The laboratory and water treatment room should be kept clean and sanitary, and fire prevention measures should be taken.
(12) Records of water treatment equipment operation and water quality inspection shall be complete and accurate.
(13) According to the water quality requirements of the boiler model of our company, the hardness of feed water is less than or equal to 0.0 15mg-N/L, the total alkalinity is less than or equal to 10 mg-n/L, and the pH value is between 10- 12 at 25 degrees Celsius.
5. Boiler equipment maintenance system:
(1) The maintenance of boiler equipment is to carry out regular maintenance and repair without stopping the boiler.
(2) Combined with the problems found in the patrol inspection, the furnace can be repaired without stopping.
(3) Main contents of maintenance:
A. Only the glass tube (plate) of the water level gauge is damaged, resulting in water leakage and steam leakage. Use another water level gauge to monitor the water level and repair the damaged water level gauge in time.
B. If it can be repaired, repair or replace the leaking valve in time.
C the pressure gauge is damaged and the dial is unclear, so it should be replaced in time.
D keep the lubricating oil path of rotating machinery unblocked and the oil cup at a certain oil level.
E. Check and maintain coal feeder, slag extractor, boiler exhaust fan, water supply pipeline valve, feed pump, etc.
F. Check and maintain secondary instruments and protection devices.
G. remove dust from equipment and accessory equipment.
(4) Requirements for safety accessory test.
A. Manual steam release or water release test of safety valve shall be conducted at least once a week, and automatic steam release or water release test shall be conducted at least once every three months.
B. When the pressure gauge works normally, clean it once a week; Traps should be calibrated at least once every six months. Parallel pressure dials should be blocked with red lines, and sealed with lead after pressure calibration.
C high and low water level alarm, low water level interlock device, overpressure and overtemperature alarm, overpressure interlock device and interlock alarm test shall be guaranteed at least once a month.
D. Equipment maintenance and test calibration of safety accessories shall be recorded in detail, and boiler room management personnel shall conduct spot checks regularly.
(5) Main contents of maintenance: Water meter glass tube (plate) should be repaired in time when it leaks water or steam; Leaked valves can be repaired in time; When a pressure gauge is damaged or the dial is unclear, it should be repaired in time, and when the lubricating oil of each rotating machine is insufficient, it should be replenished in time.
(6) Test requirements for all safety accessories: the safety valve should release steam manually or automatically at least once a week, the pressure gauge should be flushed once a week, the trap should be calibrated at least once every six months, and the working pressure should be indicated on the dial of the pressure gauge with red line.
(7) High and low water level alarms, low water level interlocking devices, overpressure, overtemperature alarms and overpressure interlocking devices shall be tested at least once a month.
(8) Equipment maintenance, testing and calibration of safety accessories shall be recorded in detail, and the person in charge shall conduct spot checks regularly.
(9) Maintenance in operation is minor repair. During the shutdown, the engineering department will make an overhaul plan or a medium repair plan for equipment operation.
6. Water treatment equipment maintenance system:
(1) Problems needing attention in the use of resin: maintaining the strength and stability of resin.
(2) When washing and backwashing, control the water quantity strictly according to the specified requirements, so as to avoid loss of resin or disorder of exchange layer.
(3) Ensure the concentration of brine and the contact time between regenerant and resin during regeneration.
(4) Pay attention to the following items when stopping using: resin conversion, moist storage and mildew prevention.
7. Boiler workshop inspection system
In order to ensure the normal operation of the boiler and its auxiliary equipment, patrol inspection shall be conducted at least once every two hours, in the following order, with the monitor as the main.
(1) Check whether the coal feeder, slag remover, secondary fan, blower and induced draft fan are normal. Whether the temperature rise of motor and bearing exceeds the limit (the temperature rise of sliding bearing does not exceed 35℃, the maximum temperature rise does not exceed 60℃, and the temperature rise of rolling bearing does not exceed 40℃, the maximum temperature rise does not exceed 70℃).
(2) Check whether the combustion equipment and combustion process are normal.
(3) Check the boiler pressure-bearing parts, the visible parts of the furnace arch and the furnace wall for any abnormal phenomena.
(4) Check whether the water level in the water tank, the temperature of the bearing and motor of the feed water pump, the switch position of each valve and the feed water pressure are normal.
(5) Check whether the dust collector leaks and the water quantity of the water film dust collector.
(6) Check the slag removal.
(7) Check whether the safety accessories, primary instrument and secondary instrument are normal and whether there is any abnormal change in the indicating signal.
(8) Check whether the oil level of lubricating parts such as the grate gearbox, front and rear axles, fans and water pumps is normal.
(9) The problems found in the patrol inspection shall be handled in time, and the inspection results shall be recorded in the operation records of boilers and auxiliary equipment.
8. Boiler workshop safety regulations:
(1) Boiler room is one of the key departments of an enterprise. Except staff, relevant leaders, safety personnel and production management personnel, other personnel are not allowed to enter without approval.
(2) The personnel on duty should stick to their posts, be vigilant, and strictly implement the safety technical operation procedures and patrol inspection system. Non-duty personnel are not allowed to switch the valves, flue and electrical switches of the boiler room without the consent of the monitor. Firefighters and water quality laboratory personnel must hold relevant certificates.
(3) It is forbidden to store inflammable and explosive articles in the boiler room. Oil drums with a small amount of lubricating oil and cleaning oil should be placed in the designated place.
(4) When the boiler is under pressure, it is not allowed to lock the door or bolt, and someone should supervise it when it is under pressure.
(5) The boiler room shall be equipped with fire-fighting equipment, which shall be placed in the designated place, and the staff shall be able to use the fire-fighting equipment.
(6) In case of boiler accident, the personnel on duty should take measures accurately and quickly to prevent the accident from expanding and report to the relevant leaders immediately.
Verb (abbreviation of verb) refrigeration process management system
1. Refrigeration room shifting system
(1) The successor shall arrive at the post in the computer room at the specified frequency and time.
(2) The handover person should make preparations in advance to learn more about the operation and records of the compressor.
(3) During the succession, if the successor fails to arrive on time, the successor shall not leave the original post.
(4) The handover should be "five-person handover" and "five-person handover"
These five points are as follows: ① The compressor and auxiliary machines are operating normally, and the pressure and liquid level are normal.
② All safety accessories and instruments are sensitive and reliable.
③ The oil level, suction and discharge pressures of the compressor are normal.
(4) Operation records, data, spare parts and tools are complete.
⑤ The machine room is clean and sanitary, and the driving is civilized.
These five nonconformities are as follows: ① Abnormal phenomena occurred in compressor and auxiliary machine.
(2) The crankcase oil level is abnormal.
(3) During the shift change, such as frost flushing and oil drainage, the shift can only be changed after everything is normal.
(4) The unfinished troubleshooting on duty was not carried out during the shift change.
(5) Don't log in without filling in the record.
(5) The successor should know the warehousing situation, temperature rise and operation situation.
(6) the successor must do a good job of succession. For example, temperature, pressure and warehousing time should be detailed and accurate.
(7) The successor shall be responsible for the equipment defects after signing the handover record.
2. Cleaning and sanitation system of cold storage room
(1) Flammable and explosive articles are not allowed to be stored in the room, and spare parts, spare parts and operating tools should be placed in designated places. Put it in order.
(2) The floors, walls, doors and windows of the computer room should always be kept clean and hygienic.
(3) Clean the area, equipment, instruments and valves before each shift.
(4) Subjective leaders should often organize relevant personnel to inspect and evaluate the cleanliness of the computer room, reward diligent and punish lazy, and achieve clean, hygienic and civilized production.
3. Refrigeration room equipment maintenance system
(1) The problems found in the inspection should be repaired in the non-stop functional maintenance.
(2) Leaking and leaking valves can be repaired in time.
(3) The pressure gauge and thermometer are damaged and the dial is unclear. Replace them in time.
(4) The liquid level fluctuation plates and pipes of high and low pressure storage tanks shall be kept clean.
(5) Check whether the safety accessories are flexible and accurate.
(6) Drain the oil collector at the specified time. For example, the condenser discharges oil once every two weeks, the high-pressure receiver discharges oil once a month, and the low-pressure receiver discharges oil once every two weeks.
(7) According to the frosting situation of the equipment and the arrangement of the workshop, frosting must be carried out in time.
(8) For each friction part, if it is found that there is local fever or the temperature rises sharply, stop the machine immediately to check the cause and repair it.
(9) Always check whether the lubricating oil is sufficient and the oil level is normal.
(10) Equipment maintenance should be recorded in detail, and managers should check it regularly.
4. Refrigeration room inspection system.
In order to ensure the normal operation of compressor auxiliary equipment, patrol inspection shall be conducted once every hour. The patrol inspection sequence is as follows, with the squad leader as the main.
(1) Check whether the compressor water pump, fan and ammonia pump operate normally, and whether the temperature of motor and bearing exceeds the limit.
(2) Whether the pressure of each instrument is controlled within the range (the oil pressure is not more than 0.4MPA, the condensation pressure is not more than 1.49MPA, and the frost flushing pressure is not higher than 0.6-0.8MPA).
(3) Check the liquid level: (The liquid level of the high-pressure liquid storage barrel shall not be higher than 80%, the lowest shall not be lower than 30%, and the lowest shall not be higher than 50% and lower than 30%).
(4) Check the crankcase oil level. The normal oil level should be between two fluctuation observation holes. (A fluctuating observation hole shall not be higher than 2/3 and not lower than 1/2) The crankcase pressure shall not exceed 0.2MPA. When overpressure occurs, open the exhaust valve to release the pressure.
(5) Check whether each pressure gauge valve is open and whether each pressure gauge is sensitive and accurate. Check whether the indicated position of the oil three-way valve is in the running position.
(6) Check the high and low pressure piping systems and equipment to see if all valves are in normal working condition.
(7) The problems found in the patrol inspection shall be handled in time, and the inspection results shall be recorded in the operation records.
5. Refrigeration room safety system
(1) Except for the relevant leaders of the computer room staff and the safety and production management personnel, other personnel are not allowed to enter the refrigeration room without the approval of the leaders.
(2) The personnel on duty should stick to their posts, be vigilant, and strictly implement the safety technical operation procedures and patrol inspection system.
(3) Non-duty personnel are not allowed to switch valves and electrical switches without the consent of the monitor.
(4) When stopping the machine, there should be a special person on duty, and it is forbidden to lock the door and bolt.
(5) The computer room shall be equipped with fire-fighting equipment and gas masks, carefully managed, and shall not be moved casually.
(6) When an accident occurs in the computer room, the personnel on duty should take accurate and rapid measures to prevent the accident from expanding and report to the relevant leaders immediately.
6. Machine repair workshop management system
1. Provisions on water management
(1) All water departments must save water, not waste it at will, and put an end to running water.
(2) The production workshop must make a water quota, save water reasonably according to the quota, and bring it into the economic assessment.
(3) The plan to increase water consumption must be put forward and reported to the competent leader for approval, and can only be implemented after being put on record in the maintenance workshop.
(4) All water users should regularly check water equipment, pipelines and valves to prevent running, running, dripping and leaking, so as to achieve civilized production.
2. Provisions on power consumption:
(1) Resolutely eliminate the ever-burning lamps. The electrical equipment (lighting) of all departments should be implemented in the team. In charge of the people, you are not allowed to change the big light bulb at will, let the light go out when people leave, and do not drive an empty car when electricity is not needed.
(2) Strengthen the management of light bulbs. Without the consent of the machine maintenance team leader, the purchaser shall not buy a light bulb of more than 200W W, and the light bulb of more than 100W shall not be used in the office, lounge and dormitory in principle.
(3) It is forbidden to use electric stoves in private parts. Anyone who uses an electric stove for heating, steaming rice or boiling water must be dealt with seriously.
(4) For heatstroke prevention and cooling in summer, the fans and air conditioners used by various departments should be controlled according to the temperature, and electricity should not be wasted.
3. Steam consumption management regulations
(1) The steam produced shall be operated in strict accordance with the process operation procedures, so as to save use.
(2) The steam department is responsible for the maintenance of steam equipment, pipelines and valves, so as to prevent the phenomena of running, running, dripping and leaking, and achieve civilized production.
(3) The indirect heating production equipment shall be provided with a condensate recovery device for centralized recovery and utilization.
(4) The heating equipment shall be equipped with special pipes, the indoor temperature of heating shall not exceed 15 degrees Celsius, and the heating steam supply time shall be 1 15- March of the following year 1.
4. Equipment maintenance management regulations:
(1) The maintenance personnel shall immediately repair the damaged equipment sent by each workshop for mechanical repair, and make repair records. 30 yuan will be fined for not maintaining in time without reason.
(2) Ensure the quality of equipment maintenance. If losses are caused by maintenance problems, the maintenance responsibility shall be investigated.
(3) The maintenance of equipment should be based on the principle of economy, try to repair the old and make use of the waste, and reduce consumption.
(4) The repaired and temporarily unused equipment shall be sent to the warehouse for registration and safekeeping.
Seven. Product inspection and test management system
1. Laboratory drug management system
(1) General requirements:
(1) All drugs must be kept in account, registered and classified.
(2) Designated personnel are responsible for the preparation, calibration, distribution and management of drugs. Each group of drugs must be registered, and a unified inventory should be made at the end of the month.
(3) Various reagents and medicines commonly used in each group must be put in order.
④ The storage, storage and use of unused drugs should be based on their different characteristics to avoid accidents.
⑤ All drugs in the laboratory shall not be transferred or lent by anyone, and special circumstances shall be approved by the section chief.
(2) Use and management of chemical reagents:
(1) The solid reagent should be packed in a large-mouthed reagent bottle, the liquid reagent should be packed in a small-mouthed reagent or drop bottle, and the photodegradation reagent should be packed in a brown bottle.
(2) The reagent containing alkali solution should use rubber plugs, and the reagent which is easy to deliquesce and volatilize and sublimate should be sealed.
③ The labels of all reagents and newly prepared reagent solutions shall indicate: name, concentration, production date and preparation date, etc.
(4) Expired reagents should be handled in time and replaced with newly prepared reagents.
⑤ Valuable drugs should be stored in special counters.
(3) Management of dangerous chemical reagents:
① Dangerous drugs should be stored, kept and used according to relevant state regulations, and strict registration procedures should be established.
(2) the use of highly toxic drugs, to go through the examination and approval procedures, and there are more than two people * * * with the use of.
(3) Flammable and explosive drugs must be stored as required, and stored separately from other combustible substances and electrical appliances and articles prone to sparks.
2. Laboratory instrument management system
(1) All testing instruments must be kept in account, classified and registered as required, and use files must be established.
(2) Precision instruments and ordinary instruments must be stored separately to ensure their accuracy.
(3) Before using the instrument, the operator must be familiar with the principle, performance and working conditions of the instrument in order to operate it correctly.
(4) Before the instrument is used, it must be checked for any abnormality, and it can be operated only after it is confirmed.
(5) The use of the instrument must be carried out as required, and no violation is allowed.
(6) Be careful in the operation process, and don't use it savagely. After use, restore the instrument to its original position, cut off the power supply and make detailed records.
(7) The specialist is responsible for precision instruments, and non-operating personnel are not allowed to touch them privately.
(8) If the instrument is damaged or broken down due to poor maintenance, it shall be reported to the management immediately, and the reasons shall be found out and handled according to relevant systems.
(9) All testing instruments, equipment and appliances shall not be checked out by anyone, and special circumstances must be signed by the supervisor.
(10) Environmental sanitation must be improved and kept clean and quiet to ensure the sensitivity and accuracy of the instrument.
(1 1) Non-operators are not allowed to enter the instrument room.
3. Laboratory safety management system
(1) Eating, smoking, laughing loudly and playing games are strictly prohibited in the laboratory. Wash your hands immediately after the experiment.
(2) The laboratory technician must be familiar with the business, strictly abide by the operating procedures, and have a rigorous and serious work attitude.
(3) The water source, power supply and fire source must be turned off immediately after use.
(4) Do not make drugs without permission or mix various chemical reagents at will to avoid accidents.
(5) All experiments that can produce irritating or toxic gases must be carried out in a fume hood.
(6) Flammable, explosive and toxic substances should be stored separately.
(7) During heating operation or explosion operation, the operator shall not leave the site.
(8) The laboratory prepares fire-fighting equipment, and the laboratory technician is familiar with the use methods and fire-fighting objects of various fire-fighting equipment.
(9) All drugs in the laboratory shall not be taken out of the room, and the remaining toxic drugs shall be truthfully recovered.
Chapter II XI Equipment Management
I. Equipment Management System
1. Equipment Planning Management System
The user department is responsible for submitting the application report for equipment addition, overhaul and scrapping, and the engineering department is responsible for organizing the audit and making the plan for equipment procurement, overhaul, renewal, transformation and scrapping. It shall be implemented after being approved by the general manager.
2. Equipment procurement management system
(1) According to the approved equipment procurement plan, the Engineering Department will organize the procurement.
(2) After the equipment arrives at the factory, the enterprise management department will organize unpacking inspection, and receive and fill in the equipment acceptance form after it is qualified. Unqualified equipment shall be notified to the engineering department in time to contact the supplier for treatment, and it is not allowed to be transferred to installation and commissioning.
3. Installation and debugging management of production equipment
(3) The engineering department is responsible for organizing the installation of the company's equipment, conducting performance tests, and making installation and debugging records.
(4) After the commissioning is qualified, the enterprise management department will organize relevant departments, including the user department, for acceptance. After acceptance, fill in the Equipment Installation and Debugging Record and deliver it to the user department for production and operation.
(5) After the installation and acceptance of new equipment, the engineering department shall timely collect the factory certificate, packing list, instruction manual, equipment acceptance sheet, equipment installation and debugging records and other technical data, file them and record them in the equipment account.
4. Operation and management of production equipment
(1) The Engineering Department organizes relevant departments to inspect the production equipment once a month, including the operation status, operation records, equipment maintenance, maintenance, hygiene and other aspects of the production equipment, and keeps the records as the assessment basis.
(2) Each user department of the equipment shall regularly check the operation status, operation records, equipment maintenance, maintenance, sanitation and other aspects of the production equipment for which this system is responsible, make records and keep them, and make the following report to the Engineering Department every month, and be responsible for the equipment intact rate, equipment utilization rate, running, running, dripping, leakage rate, accident analysis report and implementation of accident treatment measures.
(3) The user department shall operate and maintain the equipment in strict accordance with the post responsibility system, and regularly maintain and record the equipment, including patrol inspection, shift change, operation inspection, maintenance and lubrication.
(4) The pressure vessel user department should also do a good job in the safe operation management of pressure vessels.
5. Maintenance management of production equipment
(1) The Engineering Department is responsible for preparing the overhaul plan and submitting it to the General Manager for approval.
(2) According to the overhaul plan, make preparations in advance, and the engineering department is responsible for organizing and coordinating the overhaul of the whole plant.
(3) Overhaul preparation includes: implementation of overhaul project, material preparation, personnel preparation and all preparations related to overhaul.
(4) After the overhaul begins, the overhaul department shall organize personnel to complete the overhaul on schedule with good quality and quantity.
(5) Maintenance operation records shall be complete, accurate and filed.
(6) After each job is completed, the enterprise management department will conduct quality inspection together with the user department. After all the projects are completed, it is necessary to organize joint debugging and acceptance. If all items are qualified, fill in the equipment overhaul acceptance record, and the overhaul work is over.
6. Technical file management of production equipment
(1) Establish equipment account for engineering technology.
(2) The Engineering Department shall establish a file management system and handle the borrowing of files.
(3) Without the approval of the General Manager, it is forbidden to borrow technical files. Any company that violates the regulations should be severely punished.
Two. Regulations on equipment accident management
The operating rules must be strictly implemented. Anyone who violates the safety operating rules in production, has a weak sense of responsibility or is unskilled in technology, causing equipment and personal accidents, and the person who is directly responsible for the accident shall be dealt with according to the following terms:
1. If the economic loss is less than 100 yuan, it shall compensate for the direct economic loss and impose a fine on 30 yuan.
Two. Loss 100 yuan or more dissatisfied with 500 yuan, compensation for direct economic losses, and impose a fine on 50 yuan.
Three. If the direct economic loss is above 500 yuan and below 1 1,000 yuan, the direct economic loss shall be compensated and a fine of 1 1,000 yuan shall be imposed.
Ⅳ If the direct economic loss is more than 1 1,000 yuan, it shall be treated as a major accident, and the relevant management department shall analyze the accident and put forward punishment opinions, which shall be decided by the manager's office.
Five, other responsible persons related to the accident, according to the size of the responsibility, according to the above provisions, resulting in personal injury accidents. If the disabled person is the main responsible person, the company will not bear his own medical expenses and living expenses, and the enterprise will not bear any liability for injury. If the disabled person is someone else. 50% of the medical expenses shall be borne by the main responsible person and 50% by the company.
Chapter XII. Training management
I. Training management measures
1. Division of training responsibilities
(1) The company's staff training is unified and coordinated by the administrative department, and each department is responsible for it.
(2) Staff training should be based on the principle of improving the comprehensive quality and job skills of employees, focusing on practice and effectiveness, strengthening organizational management and mobilizing the enthusiasm of all parties to meet the company's development strategy and work needs.
(3) The Administration Department is responsible for formulating the overall plan and annual plan of the company's employee training, organizing and arranging business training with * * * characteristics, and coordinating the training work of various departments.
(4) Each department of the company arranges its employees to carry out business knowledge training according to business needs; According to the unified arrangement of the company, be responsible for transferring relevant personnel to participate in the training organized by the company to ensure the completion of the annual training tasks of employees in this department.
(5) Each department shall formulate its own annual training plan according to the company's annual training plan, report it to the competent manager for approval, and send it to the Administration Department for filing before implementation.
2. Training type
According to the needs of the company's business work, employee training is mainly divided into seven categories, which are introduced in the following articles.
(1) On-the-job business knowledge training: that is, business knowledge training according to the needs of each position in the company. The implementation method is as follows:
A. The department designated by the company is responsible for organizing the professional post knowledge training for the business personnel of this professional post in the company, which is generally no less than 72 hours and held once a year.
B. Each department shall organize and arrange job knowledge training for its professionals, and the personnel designated by the department shall attend training courses, the contents of which are related to the business work of the department, and the training time for each person shall be no less than 48 hours per year.
C due to organizational arrangements, the receiving unit will arrange on-the-job business training for individual employees according to specific conditions.
(2) Training of managers: aimed at improving the management level of department heads and strengthening the training of their business ability, the specific implementation is as follows:
A the training is proposed by the general manager when he thinks it is necessary and implemented by the administration department.
B the training targets are managers, supervisors, directors and other managers in charge of various departments. The training aims to cultivate managers' leadership methods, decision-making ability and management level.
C. generally, training is conducted by going out for training.
(3) New employee training: that is, annual education and training for new employees. The training content includes: the company's founding history, product information, the company's main rules and regulations, employee code, etc. , organized by the administration department. The training shall be conducted in a full-time manner, with a time of not less than 12 class hours.
(4) Relevant business knowledge training: that is, according to the development needs of the company and various departments, special lectures and special training are arranged from time to time, and the object, content and class hours are determined according to specific conditions.
(5) Post qualification certificate training: According to the relevant regulations of the state, the pre-test training for employees to obtain the post professional qualification certificate is as follows:
(6) Each employee can only participate in one kind of post qualification certificate training, and the employee shall apply to his department and report to the competent manager for approval.
(7) Training shall be conducted in training institutions designated by relevant state departments.
(8) The registration fee, book fee and expenses for post qualification certificate training shall be borne by the individual, and the training fee shall be paid in advance by the individual. After passing the examination and obtaining the certificate, the company will reimburse 50%.
(9) Other training: including other short-term training and academic education and training. The company supports employees to apply for amateur schools and arrange the examination time appropriately, and the expenses shall be borne by individuals.
(10) Training management and evaluation
A. The Administration Department shall, on the basis of soliciting opinions from various departments, formulate the company's annual training plan and submit it to the competent manager for approval before implementation.
B. Employee training expenses shall be determined according to specific conditions.
C. Employees' performance during the training period will be listed as the assessment basis, and examinations will be conducted after each training course, which will also affect employees' assessment.
D. Employees shall abide by the company's rules and regulations during the training period and be regarded as normal work.
end
end