swHow to add common language?SOLWORKSCommon language added to the library!

SolidWorks abbreviation (SW) is a new generation of Dassault introduced for the electrical industry design of mechanical 3D design tools. SolidWorks Chinese version of the use of a new parallel and serial product development environment and *** enjoy 3DCAD model, and is widely used in the design of parts, design of machinery and equipment, medical equipment, automotive, aerospace and other industries; SolidWorks can meet the user directly add a variety of auxiliary plug-ins, connect a variety of NC programming software and directly print the use of the model. Industry; SolidWorks can meet the user directly in the software to add a variety of auxiliary plug-ins, connect a variety of NC programming software and directly print the model of the use of demand. About the power of solidworks, in fact, I believe that many partners also have a certain understanding, but for the mastery of the software as well as the use of the software, may be a lot of partners are still scratching their heads! It doesn't matter, if you want to learn how to use solidworks, you've come to the right place. A wealth of solidworks boutique video courses, take you one by one to break through the software basic to advanced operation

solidworks popular video tutorials recommended:

Introduction to the software: Solidworks Mechanical Design introductory to master course

Interior Design: Solidworks engineering design to explain the chapter tutorials

Introduction to software: Solidworks measurement tool use

One-click call! SOLWORKS commonly used terms added to the library of the method

Preface

In SOLIDWORKS, often need to use a lot of terminology, and repeatedly used, this time you are still in the typing over and over again, editing, or many times CTRLC + CTRLV? Inevitably too out. Today we will introduce a way to add commonly used text to the library, when added to the library, and then need to use these specific terms or text, directly click on the library of terms or text, a key call. Specifically how to operate it, today we will take you a glance at the end.

01 editable version of the first to create a folder for storing our technical text "test", and then enter the SOLIDWORKS to open the project drawings, the need to add to the library of the "commonly used text" selected, and right-click, the following figure

The above figure, the left side of the

The above figure, the left side of the text is as follows, but also according to their own needs, or the characteristics of the enterprise to customize the required commonly used in the text, this article in the commonly used words are as follows:

"Technical Requirements:

1 unnotated dimensions of the 3D; 2 unannotated tolerance levels in accordance with the GB/T14486-MTx; 3 unannotated angle of the pull-out mold: height <3mm of the glue reduction Pulling mold 2 ° height 3 ~ 6mm rubber pulling mold 1 ° height 6 ~ 12mm rubber pulling mold 0.5 ° height ≥ 12mm rubber pulling mold 0.25 °; 4 not noted rounded Rx (optional); 5 not noted chamfer Cx (optional); 6 parting line (PL) segment difference of 0.1mm or less; (optional) 7 ejector pin (EP) segment difference of 0.1mm or less concave; (optional) 8 can not be to product Cause an impact on the product warping, burrs, scars, burns, fusion lines, flow marks and other bad; 9 location and shape of the gate shall not affect the performance of the parts and assembly; 10 appearance of the full range of dirt can not be; 11 can be assembled with the drawing number A good; (specific part number and name, optional) 12 no back material; 13 material flame retardant grade V (0, 1, 2); (optional) 14 parts color color code PANTONExxxx, color difference range: ΔE≤(0.5,1,1.5)NBS; (exterior parts); 15 Surface leather pattern see 3D attached drawing for specifics; (refer to PI manual for leather pattern specifications) 16 Materials and processing comply with the requirements of the RoHS Directive, see the provisions of LX3-009." Next, add the folder just created to the SOLIDWORKS design library (this folder can also be created in the **** enjoy the disk), the following figure: file name in the "Modify Notes" box for modification, and then added to the folder just created. 02 can not be directly edited version of the commonly used language to be created text The text of the common language to be created will be saved in the form of a block in the folder, and then dragged out again, but it can't be edited directly, you need to use the block editing method. First of all, you need to create a folder, right-click the phrase group you want to save, and click "Make Block", as shown in the following figure. You can directly drag and drop the common phrase group, you need to edit, click on the left side of the edit or double-click, you can jump to edit the block, the block can be directly positioned in the location of the required display, the following chart:

So, today's "one-click to invoke the SOLWORKS commonly used words to add to the library of the method" on the end of the end of the sharing here! We must learn to see more, practice more, think more, learn more, I hope we can all learn solidworks as soon as possible! Here, but also for you to provide more courses to learn, click the link: