In accordance with the requirements of the tender documents required to fill in the first column of the goods specifications, the second column of goods bidding specifications are best all in accordance with the first column of the bidding for goods specifications written in the third column are filled in line with.
Tender specifications deviation table should be regarded as the tender documents in the commercial response part of the most important chapter, a lot of information is based on the parameters here.
Table header before the information: this place in general is the project name, project number, subcontract name of the three, but some companies are the name of the bidder, project name, subcontract name of the three, so it is important to look at this place, do not get it wrong (followed by itemized quotations, list of goods, technical deviation table and business deviation table is the same).
Project name (or the name of the bidder), the project number is not said, the subcontract name is filled in if there is no time to fill in the blank, to fill in the "/";
The table behind the information: the table behind the bidders are signed and sealed, this place is basically the same, the difference may be Is called different, for example: some call the bidder, and some call the name of the bidder, the nature of the same, although the wrong does not have much impact, but for insurance purposes, it is best to check clearly;
The number of forms: some in the bidding parameters are divided into a number of forms, such as: software parameters, hardware parameters, etc., at this time also need to be consistent with the bidding, divided into a number of corresponding forms to respond;
The contents of the table: this part is the need for special attention to the place, generally including the serial number, service content, bidding documents, clause number, bidding requirements, bid response, deviation, description of several items, here focus on the bid response to the part, as follows:
1, serial number: can be handwritten can also be automatically generated, but be sure to be consistent with the second item "Name" is consistent with the second item, with the name of the item changes;
2) service content: the name must be consistent with the name written in the technical parameters of the bidding documents. If it is an item contains several small items, then you can not write only the large or only small items. The correct approach is 1 column split into 2 columns, the size of the item are written in, corresponding to the first column of the number to the large items, followed by several columns of parameters to the small items;
3) bidding documents, clause number: because many bidding documents are more confusing, so try to find the smallest item of the number of the clause, corresponding to the most accurate position, the bidding documents, if it is really can not find very accurate information, then Corresponding to a relatively accurate position;
4) bidding requirements: also known as bidding parameters, in accordance with the corresponding content copy and paste can be;
Tender Response: should be considered the most important place in this chapter, you need to focus on the preparation of the bidding parameters corresponding to the bidding parameters write their own bidding parameters, need to pay special attention to is that, in order to save time and copy and paste directly over, so that it is Will be abolished, here are a few tips that will allow you to write faster, as follows:
If this bid is determined to win the bid, then this piece of writing needs to be very serious, must ensure that the bidding parameters can not be a response to the omission of a line, you can be more, but definitely not less; if there is no response to the bidding can be copied, a little change in the way of expression. way;?
If this tender is used to bid, then the response content is relatively simple, generally are the bidding parameters directly copied over, but in order to avoid the abolition of the bid, it is best to paste over the parameters of the modification, such as modification of the expression of the way, change the position, etc. are feasible;
If this tender room used to win the bid, but the lack of good parameters to respond to, then you can copy the bidding parameters, then the first, the first time to copy the tender parameters. , then you can first copy the tender parameters, and then modify, the longer part of the split into a number of, it is split into detailed instructions, the tender is not sorted as much as possible in the content of the order, thus looking different from the other, but read the contents of the same can be.
6) deviation: most of them are "no deviation", there is nothing more to elaborate;
7) description: generally "no".
Expanded:
Technical deviation form is a collective term for technical specification deviation (form) and technical parameter deviation (form). It is a
concept in the context of commercial bidding or commercial contracts. Broadly speaking, it is a commercial contract or commercial bidding documents, technical (contract) documents in the quite important supplementary documents.
Technical specifications deviation table: technical specifications deviation table is intended to list and the requirements of the tender documents do not comply with the provisions, but it is recommended to utilize this table
The full technical indicators. If there is a deviation from the requirements of the technical specifications of the bidding documents, fill in, if the technical specifications and the requirements of the bidding
documents can not fill in the same.
Commonly used specific form format:
Technical specifications deviation form
Bidder's name: (seal) Bidding number:
Bidder's representative signature:
Technical deviation form
Tendering No.
Tendering name:
Tendering project name:
Reference: