I have practiced installing successfully, do not dare to share alone, special take out and share with you.
I. Introduction:
After two days of study, in their original car navigation above the successful installation of the DSA Good Leader and multi-map software.
The following is the original picture of the tube side of the DSA Good Leader.
The main functions of DSA Good Leader are:
1, real-time speed, exercise direction, electronic eye, red light prompts, speeding prompts, speeding prompts, MP3 playback and so on. There is also a driving record function, such as you run 50 kilometers, in the exercise will have the highest exercise speed, minimum, average, and the time used.
The following detailed method:
1, first of all, to find out their navigation "port number", and "rate" and so on this very important parameter. For example, my port number is com6 rate is 4800.
2, how to check their navigation "port number", and "rate", there are several ways:
(1) consult the navigation dealer or manuals and so on.
(1) Consult the dealer of the navigation or the manual or something like that.
(2) Through the relevant special tools. For example, there is a "GPS test tool"
(3) Check the parameters in the map file. I myself use this method to view. The above two basically can not be realized. Here is the main map parameters to see
"Port number", and "rate"
First: Keliad map file location: NaviOneNaviResFileNaviConfig .dll Need special Keliad port modification tool
This is the Keliad map port view and modification tool.
Figure 3F0 followed by com4 This is the port number, if you modify the above box, enter the number 0-9, press the Enter key to modify.
490 in the figure behind the 4800 this is the rate. If you modify the above box, enter the number, press the Enter key to modify.
Construct the other do not move.
Second, the intercity map port view and modify,
In the intercity map of the root directory below to find "comm_config.txt" this file. The first 9 is the port number, and the last 4800 is the rate. This is easy to modify. Don't lose the comma in the middle.
Third: DaoDaoTong map port view and modify, in the root directory to have a config.txt, open the last two is, the last one is the rate, the penultimate is the port number.
The fourth: the map port and speed modification of the higher Germany is more troublesome, here will not say, if you need or other maps to me to leave a message.
3, the next step is to modify the DSA Good Leader port rate number to be the same as the navigation above, or not search the satellite. If this step is set up successfully, the DSA Good Leader can be used normally.
4, through the DSA good collar to make multi-map can be used normally and search for satellites. There is a "protconfig.txt" under the root directory of the DSA Good Leader, which is to modify the port and rate of the DSA Good Leader.
The first one, comport=6, is to modify the port of the DSA, and the second one is the rate. The third is the virtual port number.
The first two settings should be the same as the port rate above the navigation.
The third virtual port number should be the same as the map port number of the guide.
Then set the port and rate of the DSA Good Leader and the navigation above the same, in the modification of all the maps in the port number and rate and "protconfig.txt" file in the last item to be the same. Otherwise, the map can't search the star again.
4, the last step. Through the navigation to guide the DSA Good Leader normal start work:
Take my Kelilong as an example: (my original navigation inside the map is Kelilong)
In the root directory there is a "maplaunch.ini" this file is the boot configuration file. The following picture:
navione this is the map directory of Kelilong.
Open the maplaunch.ini configuration file: as shown:
The first item: is the boot path:
The second item: is the boot background image
The third is not used.
The function of this file is, when the navigation is turned on, the navigation to load the map is necessary to need a configuration file to boot start the map start. The boot config file in my nav is the one above.
The original file is a direct boot map, we now want to run the DSA first good collar, we need to change the path and file name.
For example:
path = dsa\dsa.exe (The path here is very important, must be the same as the memory card. Otherwise, it will not be able to boot)
Because the navigation is different, the guidance inside may also be different, so you need to know how to complete the guidance on their navigation.
Here basically has been successful, as long as the setup of the car can start the DSA normally, the next setup in the navigation above can be operated.
Load MP3 songs in the DSA, study it yourself, it's very simple.
By and large, it is written here, but also written more verbose. I'm not sure if I can understand what I'm talking about, but I'm sure I can understand what I'm talking about.
The last thing you need to pay attention to is, don't put the map of the port and navigation and DSA are set to the same, so it will conflict.