Second, cut, shear and press according to the production plan, ensure the size and accuracy of blanking and pressing, meet the specified requirements, and carefully remove flash burrs.
Three, the board should fully consider the release of internal stress, in order to reduce deformation.
Four, when assembling structural parts, it is necessary to check whether the parts transferred from the previous procedure are qualified, and the welder should conform to the requirements of the drawings and control the flat-fell seam gap to facilitate welding in the next procedure.
Five, the first active inspection, self-inspection, completes the identification of parts, fill in the quality record.
Six, reasonable and orderly placement of spare parts, timely cleaning up the waste on the job site, to meet the requirements of site management.
Seven, timely completion of production, quality and safety indicators.
Main responsibilities of riveting job 2 responsibilities of riveting job
1, study hard and strictly abide by the company's rules and regulations, do not violate labor discipline, do not operate illegally, and take direct responsibility for the work of this position.
2, strictly abide by the riveting work safety operation procedures, careful operation, the tools used must be in good condition, safe and reliable.
3, mount guard must be dressed in accordance with the provisions. Keep and use all kinds of protective equipment and fire fighting equipment properly. Keep the working environment clean and tidy, and do a good job in civilized production.
4, into the container maintenance procedures must be complete, reliable safety measures, before entering the container operation.
5. Correctly analyze, judge and handle all kinds of accident symptoms, and nip the accident in the bud. When an accident occurs, report it to the superior in time and truthfully, protect the scene and assist in accident investigation.
6. Take part in the study, raise awareness, do all the work carefully and do a good job in civilized production.
7. Consciously accept the inspection and supervision of the supervisor. Have the right to refuse the instruction of illegal operation and discourage and stop others from illegal operation.
Safety operation procedures for riveters
1. Before working, carefully check whether there are burrs and scars on the tops of various tools used: tools that bear hammering, such as large and small hammers, flat hammers, punches, etc., whether there are crack marks on the hammer handles and whether they are firmly installed. It is forbidden to use the tops of various hammering tools in quenching state.
2. Wear protective glasses when shoveling, splitting and riveting, and don't operate on people. When using pneumatic shovel, the shovel head must be removed at work to avoid accidents. Please wear protective earplugs when the noise exceeds the regulations.
3. At work, when using hydraulic press, friction press, edge planer, shearing machine and other equipment. You should first check whether the equipment is working properly and strictly abide by the safety operation rules of the equipment.
4. When chiseling steel plates, circular objects (such as iron pipes, iron balls, iron bars, etc.) are prohibited. ) to make the following pads, so as not to roll and hurt people.
5. When using the crane to rotate the working object, the staff must leave the dangerous area, and the spreader used must be carefully checked in advance, and the safety operation procedures for crane lifting must be strictly observed.
6. When using a sledgehammer, pay attention to the scope of the hammer. When hammering, look forward and backward. No one is allowed to stand on the opposite side to prevent danger when swinging the hammer.
7. The heated materials should be stored in a fixed place. When moving, use dripping test and other methods. After cooling, you can move it by hand to prevent burns.
8. When using the heating furnace, pay attention to whether there are wires or flammable items around. When the ground furnace goes out, the air door should be opened to prevent explosion. After flameout, check it in detail to avoid re-ignition. Heated materials should be stored in a fixed place.
9. When riveting the workpiece, if the hole is wrong, it is not allowed to try by hand. You must align the pole with a steeple and then pierce the nail. When hitting the punch, no one is allowed to stand in the direction where the punch passes.
10. When working high above the ground, fasten your seat belt, observe the safety regulations for working high above the ground, and carefully check whether the operating frame and springboard are firmly erected. When working on a circular workpiece, the bottom must be padded. It is possible that no one is allowed to stand on it when rolling.
1 1. When throwing hot rivets from a distance, pay attention to whether there are other workers around. In order to prevent pedestrians from passing, fences and warning signs should be set around the work site. The rivet picker should pick it up next to him.
12. When connecting the compressed air pipe (belt), first open the air door and blow the dirt in the air pipe (belt) before connecting. When the blockage is found to be penetrated by the iron bar, the head must be avoided. The trachea (belt) is not allowed to cross the track.
13. When nailing and sewing, you must wear protective glasses; You are not allowed to wear gloves when hitting a sledgehammer.
14. When using nail gun, nail should be installed first, and then nail should be installed. After loading the nail gun, you are not allowed to knock the launch tube with your hands and hit the human body at any time. If you don't need to shoot for the time being, you must remove the nails and nails immediately.
Main responsibilities of riveter post 3 1 scope
This standard specifies the quality requirements, responsibilities and authority, work contents and requirements, inspection and assessment contents of riveters.
This standard is applicable to xxxxxx riveter post.
2 Quality requirements
2. 1 ideological style: see general working standards for workers.
2.2 Education: Junior high school or above.
2.3 After technical training, you should know that you will pass the exam.
2.4 Pass the knowledge study test of safety, fire prevention and TQC (Full Responsibility Quality Management).
2.5 Have good professional ethics. Obey the distribution and obey the command.
3 responsibilities and authority
3. 1 Be responsible for the quality of your work and products.
3.2 Be responsible for equipment and personal accidents caused by illegal operation.
3.3 Be responsible for the safe and civilized production of this unit.
4 Work content and requirements
4. 1 Implement general working standards for workers.
4.2 To undertake the lofting, marking, blanking, processing, prefabrication, assembly and riveting of all metal structures arranged by the superior.
4.3 Before taking up the post, you must wear labor protection articles in accordance with the regulations.
4.4 Conscientiously implement the "five-sequence method" in the production process:
4.4. 1 First standby: prepare product drawings, process technical documents, tooling and measuring tools.
4.4.2 Second look: Understand drawings, processes and standards, define tasks, and check measuring tools and processing objects.
4.4.3 "Three Suggestions": When problems are found, they shall be submitted to relevant departments for handling in time.
4.4.4 Four services: work according to regulations and production in strict accordance with drawings, processes and technical standards.
4.4.5 Five inspections: Deliver inspection according to the specified procedures, and put into production only after the first inspection is qualified.
4.5 All kinds of equipment used should be customized, and the operators should pass the technical examination, operate with certificates, and carefully maintain the equipment.
4.6 Adhere to safe and civilized production.
4.6. 1 When using pneumatic drills, hand electric drills, manual grinding wheels, plate benders, presses, plate shears, drilling machines and other equipment, safety operation procedures must be strictly implemented to avoid equipment and personal accidents.
4.6.2 When cutting materials and work, the workpiece must be placed smoothly, and attention should be paid to pedestrians around and in the corridor to prevent flying and hurting people.
4.6.3 The work site shall be kept clean, tidy and standardized at any time, and all kinds of parts and surplus materials shall be classified and stored, and surplus materials and waste materials shall be cleaned and recycled in time, so as to be cleared after work.
4.7 Tools, molds, fixtures, materials, blanks, workpieces and products shall be placed reasonably, stably and reliably.
4.8 When receiving spare parts, check according to the drawings and check whether the material records are clear.
4.9 The operation must comply with the provisions of safety operation regulations and process regulations.
4. The10 toolbox should be kept clean and free of sundries, and the tools should be put away. Put it in order, and the accounts, cards and things are consistent.
5 Inspection and evaluation
5. 1 The monitor is responsible for the supervision, inspection and assessment of the implementation of this standard, and leaders at all levels and professional functional personnel randomly conduct inspection, assessment and guidance.
5.2 The assessment results of this standard (including general working standards for workers) are linked to the economic responsibility system and relevant regulations of this workshop, and rewards and punishments will be honored.
Main responsibilities of riveter position 4 1. Job responsibilities
1. We must abide by the rules and regulations formulated by the company, obey orders, stick to our posts and strictly abide by labor discipline.
2. Under the leadership of the room director, complete riveting inspection of container products and other work assigned by the room director.
3. Work must be serious, fair, accurate and timely.
4. Strictly implement the national standards and relevant laws and regulations for the manufacture and inspection of pressure vessel products, and establish the idea of "quality first" and "customer first". Enhance the sense of responsibility and control the quality.
5. Strictly implement the relevant provisions of the pressure vessel manufacturing quality assurance system.
6. Be responsible for inspecting and marking products according to drawings and process standards. The whole process of finished product quality inspection is from the blanking, assembly, pressure test, painting and packaging of product parts.
7. Be responsible for verifying that all parts used for assembly have passed inspection and acceptance, and can be assembled only after having qualified reports and qualified marks.
8. Check the assembly procedure and process quality to ensure the assembly according to the drawings.
9. Completion inspection: responsible for the comprehensive inspection of all assembly control points. And notify the inspector to go to the site for inspection and confirmation, mark and record after passing the inspection, and draw the steel seal distribution map of product materials.
10. Be responsible for checking the whole process of hydrostatic test, and notify the inspector to go to the site for inspection and confirmation. After the final inspection of the pressure test is qualified, fill in the pressure test qualification report.
1 1. Responsible for the inspection of paint and packaging quality.
12. Fill in the quality record according to the specified form and be responsible for submitting the product inspection record to the inspector, and be responsible for the accuracy and reliability of the inspection record. The handwriting of inspection records shall be neat, clear and tidy.
13. Identify and report nonconforming products according to regulations, and conduct re-inspection and re-labeling after treatment to prevent untreated nonconforming products from becoming invalid.
14. Pay attention to the equipment and inspection tools. Do a good job in safe production and civilized production.
15. Work records should be done carefully.
Two. Entry standard
1. Age: in line with working age.
2. Gender: male or female.
3. Education level: high school or above.
4. Physical condition: good health, no infectious diseases, and can adapt to the working environment of high-intensity mental and physical labor.
5. Love product quality inspection, have a strong sense of responsibility, be honest and honest, and be able to study hard.
6. Qualification for professional skill appraisal: Engaged in riveting work for more than five years, and obtained professional qualification certificates for primary and above riveting posts.
7. Professional Ethics: Implement the general standards of corporate behavior and cultural ethics of Shi Lan Group.
8. Practical knowledge:
(1) Master the working procedures and inspection procedures of pressure vessel inspection posts;
(2) Be able to understand the drawings, technical documents and process regulations of pressure vessel products;
(3) Understand the structure of the company's leading products;
9. Professional knowledge requirements:
(1) Have basic theoretical knowledge of elementary mathematics and mechanical drawing;
(2) A preliminary understanding of national standards, regulations and policies for pressure vessels;
(3) A brief understanding of the manufacturing process of pressure vessels;
(4) Understand the brands, technical requirements and process performance of commonly used materials;
(5) Understand the use and maintenance methods of measuring instruments and testing tools;
10. safety knowledge: understand the laws, regulations and policies of the state and enterprises on safety production.
Main responsibilities of riveter post 5 1. Before construction, be familiar with the process drawings, make clear the technical requirements, and draw up a safe construction plan.
2. Abide by rules and regulations and safety operation procedures, observe labor discipline and construction specifications, and do not operate illegally.
3. Wear labor protection articles correctly according to regulations, use protective facilities correctly, and check whether the safety devices are in good condition in time.
4, correct operation, careful maintenance of equipment and tools, keep the working environment clean and tidy, do a good job in civilized production.
5. Constantly identify hazards and environmental factors, and take reduction measures to minimize them. Once an accident occurs, it should be reported truthfully immediately, and control measures should be taken to protect the scene and cooperate with the accident investigation.
6. Actively participate in various safety and environmental protection activities, job training and accident plan drills.
7, have the right to refuse illegal instructions, discourage and stop others illegal operations.
8. Be responsible for the safety and environmental protection of this position.