What are the maintenance rules for washing equipment?

Dryer, every day: the first time you turn on the dryer, you must first open the trap bypass valve, drain the condensate in the heater and steam piping, and then close the trap bypass valve. After each day's work, drain the residual water, open the front door, and close the main steam inlet valve and the main air inlet valve. Dry cleaning machine: every washing 2 times: clean up the trap filter; every washing 100 times: clean up the nylon filter; every washing 200 times: clean up the liquid-water separator; every washing 300 times: clean up the liquid level pipe of the trap and the safety valve of the distillation tank; every washing 500 times: clean up the third part; every washing 3,000 times: clean up the liquid tank. Folding machine, each time before starting to check: 1, the machine has a stagnant fabric or clogging fabric, first to remove. Because the thin cotton belt or cotton yarn will cause the photoelectric switch to blacken or change the effective diameter of the rollers.2. If the machine is down for a long time, before starting the machine, it should be run for 5 minutes according to the normal program, so that you can make sure that the machine is running normally (no noise sound). Every year: check the wear and tear of the clutch and brake, and adjust or replace them accordingly if needed. Every five years: Replace the PLC battery. When in doubt, ask the manufacturer. Trough ironing machine, 1, regularly check the use of the rollers wrapped outside the felt and spring wear, found that wear and tear is serious, should be replaced in a timely manner, so as not to continue to run damage to the fabric and ironing trough working surface. 2, if the equipment is not used for a longer period of time, should be excluded from the pipeline water first, and the ironing trough with wax and protective grease and then wrapped the equipment with a plastic sheet. Roller ironing machine, 1, steam supply, when the steam reaches the specified pressure, open the circuit pipe on the bypass valve, condensate drainage into the downstream pipe until the steam flow, and then close this valve. 2, in the process of ironing machine work, you should always pay attention to observe the rotary joints whether there is a leakage of steam phenomenon, and if there is a replacement of the graphite ring and sealing ring. Users should note that usually when the graphite ring is just replaced, there will be a small amount of steam leakage, but after the ironing machine has been working for some time, the graphite ring will be ground, and the steam leakage phenomenon will disappear automatically. If the steam leakage phenomenon does not disappear, the rotary joint should be replaced. Dryer, 1, often clean the surrounding environment, remove the radiator above the debris and the following filter on the debris. 2, often check the steam pipeline and hydrophobic pipeline leakage and smooth situation. 3, often check the operation of the transmission system, adjust the tightness of the triangle tape. 4, often check the electrical components of the contact and insulation. 5, often to the transmission bearings to add lubricating oil. 6, every six months, please give the Equipment maintenance. Ironing machine, 1, machine use for a period of time, to each turn committed to the parts of the regular filling of lubricating oil. 2, machine operation occurs not speed murmur, should be immediately shut down for maintenance. After half a year of normal use, the machine should be shut down for maintenance, replace the oil in the reducer, and add lubricant to each bearing respectively.3. If the machine is not used for a long time, the bloomers should be removed, and the various transmission parts of the roller garment should be wiped clean and sealed.4. The safety valve should be checked regularly to see if it works properly, and it must be sent to the labor department for calibration every year.5. According to the safety supervision regulations of pressure vessels of the State General Administration of Labor, users should carry out an appearance inspection of the roller at least once a year. Appearance inspection, such as the discovery of Hu surface cracks, deformation, local overheating and other abnormal phenomena, should be dealt with in a timely manner, if necessary, replace the drum. Washing equipment tips, washing equipment belongs to the large-scale washing equipment, complex structure, especially automatic industrial washing machine, divided into manual process and automatic process, but also includes the addition of soap, so for the first time the use of automatic industrial washing machine washing workers, will be due to improper operation, resulting in damage to fabrics, the more serious will cause personal injury. The following eight points, washing equipment users should pay special attention to: 1, prohibit the washing of fabrics other than anything else. 2, prohibit the washing of fabrics soaked in petroleum, which is likely to cause an explosion. 3, prohibit the washing of industrial washing machine parts, otherwise the liner will receive serious damage. 4, liquid detergent to be added directly through the soap box of the equipment, prohibit the addition of soap in the front door. 5, in the washing machine operation and heating time It is prohibited to open the door of the soap box to avoid steam or water scalding.6. It is prohibited to put hands or other objects into the roll cage before the washing machine completely stops. This will lead to serious injury.7, static operation of the overshock switch damaged or removed industrial washing machine, if the machine load is seriously unbalanced, due to overshock, can cause serious personal injury and damage to the washing machinery itself.8, before each washing cycle, the solid detergent must be diluted with water and put into the soap box, it is forbidden to add soap solution in the automatic industrial washing machine in the process of washing, it's good to The time to put the soap solution is after the water, before heating. Laundry washers should be in strict accordance with the operating steps of the automatic washing machine, the above points prohibit the operation of the steps, must be strictly remembered, if you encounter a washing machine failure, please contact the company in time to local dealers, do not repair by themselves. To learn more about the information, you can consult the official website of Oriental Reliance Laundry,