Camera is a video input device, a kind of closed-circuit television, is widely used in video conferencing, telemedicine and real-time monitoring. Here is my collection of how to install a single camera, for your reference, I hope to help friends in need.
How to install a single camera
Notes:
(1) line
① According to the length of the line carefully wired, pay attention to the model, interface, line normal loss and normal transmission distance.
② Before energizing the test, you must check all the lines and voltage match once again to avoid damage to the equipment after energizing.
(2) environment
① located in a strong electromagnetic interference environment, the camera installation should be isolated from the ground insulation;
② outdoor installation should be coordinated with the surrounding environment, and take protective measures, such as adding a shroud.
Here, by the way, I would like to tell you about the installation of the shroud (must be installed after the above process 'step 3'): open the shroud of the upper cover plate and the back plate, pull out the fixed metal piece, the power adapter into the camera, reset the upper cover plate and the back plate, straighten out the cables, and fixed to the bracket.
Preparation:
(1) Common tools
Impact drills, levels, screws, screwdrivers, brackets, rise plugs, small hammer, insulating tape, PVC pipe, stripping pliers, etc.
(2) Equipment
Camera, power cables, video cables, control cables, BNC interface, Hard disk recorders, etc.
(3) Determine the installation location of the camera and the placement of the back-end equipment, and all the equipment first a test to determine whether the voltage, wiring and other work to match the actual installation project.
Installation process:
① first mount the bracket, remember to check the bracket screws and camera base screws are appropriate, pre-buried pipeline interface is properly handled as well as whether the cable is smooth and other details;
② to the camera on the lens, in the process of the process must pay attention to the lens can not touch the hands and CCD (Charge-Control Device), and the CCD (Charge-Control Device), and so on. and CCD (charge-coupled device);
③ power, connect to the host or the site to use the monitor, adjust the aperture and focus;
④ the camera is fixed to the bracket, screwdriver to tighten, make sure that it is firm, and remember not to get the negative poles anyway;
⑤ and the hard disk recorders wired to the soldered video cable BNC plug into the video cable interface;
⑤ and the hard disk recorders wiring, soldered video cable BNC plug inserted in the video cable
⑥ Insert the output plug of the power supply into the power jack of the surveillance camera;
⑦ Connect the cable to the control host or monitor;
⑧ Turn on the power to the installed equipment, and adjust the camera's angle, parameters and other settings through the monitor.
How to install a video surveillance camera
1. Prepare the relevant devices and tools
First of all, it is necessary to prepare the work of the bracket, rise plugs, screws, screws, screwdrivers, hammer, drills and other parts and tools for work, select the installation parts on the wall or other places. Measurement of the installation site, the rise of plugs and screws to modify the data, check the pre-buried pipeline contact, and test and monitor the camera's circuitry can work properly, after all the testing is complete, we can begin to enter the formal camera equipment installation program.
2. Installation of the camera
After the preparatory work is completed, you can start the installation of the camera; first of all, take out the camera, based on the camera's relevant instructions, select the appropriate model and size for installation. Of course, in the installation, be sure not to touch the camera lens, to prevent scratching and damage, in addition to the installation of the screws and the installation of the plug, but also pay attention to the location of the camera for a stable fixed. Prevent the position of the camera from deviating. In this process, the installation of the bracket should also be very careful, pay attention to fixed.
3. cover installation
In order to reduce the external environment such as bright light, rain, sand and other damage to the camera and camera equipment and impact, generally we need to install the camera cover, so after the camera is fixed installation, we can start to install the cover. The first thing is to open the cover and the entrance, and then pull out the blocking metal piece, and ensure that the camera is fixed, and then in the shroud inside the power adapter, after the completion of the cover, the cover, the cable equipment, fixed, and then mounted to the bracket, so that basically completed the installation of the shroud.
4. Post-processing
Here, we have to install the video cable, where the video cable is pre-processed, after the installation is completed, it will be connected to the BNC, and make sure that the device is not easily affected by the fixed.
Connect the other end of the power adapter, the power output, to a power supply such as an outlet, and make sure they are working properly and are secured.
Connect the camera to the host computer and the controller, mainly by connecting the other end of the cable to the relevant connector on the host computer and fixing it.
Turn on the switch and the power control, after the installation is complete, adjust the camera angle, so that the camera's image capture can reach the best angle.