SolidWorks abbreviation (SW) is a new generation of Dassault introduced for the electrical industry design of mechanical 3D design tools. SolidWorks Chinese version of the use of a new parallel and serial product development environment and *** enjoy 3DCAD model, and is widely used in the design of parts, design of machinery and equipment, medical equipment, automotive, aerospace and other industries; SolidWorks can meet the user directly add a variety of auxiliary plug-ins, connect a variety of NC programming software and directly print the model use needs. Industry; SolidWorks can meet the user directly in the software to add a variety of auxiliary plug-ins, connect a variety of NC programming software and directly print the model of the use of demand. About the power of solidworks, in fact, I believe that many partners also have a certain understanding, but for the mastery of the software as well as the use of the software, may be a lot of partners are still scratching their heads! It doesn't matter, if you want to learn how to use solidworks, you've come to the right place. A wealth of solidworks boutique video courses, take you one by one to break through the software basic to advanced operation
solidworks popular video tutorials recommended:
Software: Solidworks Mechanical Design introductory to master course
Interior Design: Solidworks engineering design to explain the chapter tutorials
Interior Design: Solidworks engineering design to explain the chapter tutorials
Introduction to software: Solidworks measurement tools
Solidworks modeling exercises of the fan
Today we want to share with you is the appearance of the fan styling design examples. The modeling is not difficult and can only be considered entry level. If you already know how to do it, you can look at the drafting process purely as a pastime. If you are still in the introductory stage, to practice a little will not be disappointed.
The following are the steps for modeling.
1. Sketch a circle in the right-hand datum and stretch it to form a tab. Bump height: 8, draw angle: 17.
2. Draw a cylindrical bump to stretch and grow to the other side with a height of 8.
3. Offset the rear-view datum to create datum 1.
4. Create a sketched line on the front-view datum to create the stretched surface.
5. Create a sketch curve on datum 1 and do a clipping of the surface created in step 4. This is how we get the surface created.
6. Twist the surface created in step 5 and set the parameters as shown below.
7. Make a circular array of the fan blades from the previous step.
8. Draw a circle in the top view datum and do a solid rotation.
9. Offset the right view datum by 15 to create datum 2.
10. Create a camber stretch in datum 2. Height 2.
11.Create a datum 4 so that it passes through the following points and is parallel to datum 2.
12.Draw a spline curve in the front view datum plane.
13. Draw a circle in datum 4.
14. Create a solid scan using the sketched circle from step 13 as the cross section and the sketched spline from step 12 as the trajectory.
15.Create an array of circles, number 40.
16.Offset the right view datum to get datum 5.
17.Make a mirror image with datum 5 as the reference.
18.Draw a circle to create a stretched tab, height 5.
19.Offset the right view datum by 50 to get datum 6.
20.Draw two circles and use them to make a tab release.
21. Create a chamfer R5 for the following edge line.
22. Offset the top view datum by 130 to get datum 7.
23. Draw two sketch curves to create the tab release.
24.Offset the bottom surface of the fan neck by 182° to create a datum 8.
25.Offset datum 8 to create datum 9.
26.Offset datum 7 to create datum 10.
27.Draw two rectangles to make a boss release.
28.Create chamfers for each of the following edges.
29. Create a stretched tab with a height value of 5 and an extraction angle of 8.
30. Create a chamfered corner R1 for each of the following edges.
31. Array the keys 3 more times out, with a spacing of 10.
32. Create a stretched tab with a height value of 2 and an extraction angle of 16.
33.
34. Create a chamfer R0.5 for the following side line.
35. Create a chamfer R0.2 for the following side line.
36. Create a chamfer R5 for the following side line.
37. Create a parting line for the following.
Modeling complete.
So, today's "Solidworks modeling exercise of the fan" is shared here to the end! We must learn to see more, practice more, think more, learn more, I hope we can all learn solidworks as soon as possible! Here, but also to provide you with more courses to learn, click the link: