what should I do if the router of p>TP-link can't get on the management page?
1. Enter the login address and find that the webpage cannot be opened, as shown in the following figure. First, right-click the wireless network signal, as shown in the figure below. Select Open Network and * * * Enjoy Center, enter Network and * * * Enjoy Center, and click Change Adapter Settings, as shown in the figure below. Right-click the wireless network card and click Properties.
2. If none of them work, it is caused by a router failure, and the router can only be repaired or replaced.
3. Replace the browser or computer; Use the mobile App to manage the router; Reset the router. Check the connection between the terminal and the router (the operating computer can connect to the router through network cable or wireless way.
What is the reason why the URL set by TP-Link wireless router can't be opened?
What is the reason why the URL set by TP-Link wireless router can't be opened?
1.-Check the IP address of the computer. If the computer doesn't specify or get the correct IP address, it will lead to the failure to log in to the management interface. Note: If the terminal is connected to the router wirelessly, you can skip this step. Please be sure to set the IP address of the operating computer to be obtained automatically.
2. The TP-LINK wireless router can't enter the setup interface, because: the router's login address is wrong; Router connection error; The router conflicts with the Modem address; Router failure.
3. or if you want to reset your router, you can restore the factory settings for this TP-LINK router first, and then enter the router according to the address on the back of the TP-LINK router to set it. So you can reset your router. We can solve the problem.
what should I do if the p>TP-LINK router settings page cannot be opened?
what should I do if the p>TP-LINK router settings page cannot be opened?
1. It is recommended to use wireless connection to log in to the router management interface. Wireless connection: the wireless terminal needs to connect to the wireless signal of the router. When factory setting, the default signal of the router is: TP-LINK_XXXX, which is not encrypted. If the wireless signal has been modified, just connect the modified signal.
2. or if you want to reset your router, you can restore the factory settings for this TP-LINK router first, and then enter the router according to the address on the back of the TP-LINK router to set it. So you can reset your router. We can solve the problem.
3. Your computer may not be set to automatically obtain the IP address. First, you need to log in at 19161. If it doesn't work, it is suggested to reset the router: change the local connection to automatically obtain the IP address.
4. Hello ~ Can't you open 19161? You need to make several settings, and set your TCP/IP to get it automatically, otherwise you can't log in. Or 1916X format.
5. If there is a problem with the network cable connecting the computer and the TP-Link router, it will also cause the setting website to be unable to be opened after being entered in the browser; So you can try to change the network cable between the computer and the router.
the p>TP-LINK wireless router cannot enter the wireless routing settings page.
the p>TP-LINK wireless router cannot enter the wireless routing settings page.
1. TP-LINKtl-wr72n can't enter the router setting interface, which is caused by the network setting error. The solution is as follows: enter the login address and find that the webpage cannot be opened, as shown in the following figure. First, right-click the wireless network signal, as shown in the figure below.
2. Your computer may not be set to automatically obtain the IP address. First, you need to log in at 19161. If it doesn't work, it is suggested to reset the router: change the local connection to automatically obtain the IP address.
3. It is recommended to use wireless connection to log in to the router management interface. Wireless connection: the wireless terminal needs to connect to the wireless signal of the router. When factory setting, the default signal of the router is: TP-LINK_XXXX, which is not encrypted. If the wireless signal has been modified, just connect the modified signal.
4. or if you want to reset your router, you can restore the factory settings for this TP-LINK router first, and then enter the router according to the address on the back of the TP-LINK router to set it. So you can reset your router. We can solve the problem.
what is a connector?
what is a connector?
1. A connector is also often called a circuit connector. As the name implies, it is a conductor device that bridges two conductors in a circuit so that current or signal can flow from one conductor to the other. Electronic connector is a kind of motor system, which can provide a separable interface to connect two sub-electronic systems.
2. A connector is an electronic component, which is used to connect different parts of a circuit, and can connect electronic devices, circuit boards, cables, etc. The function of connector is to transmit electric energy, signals and data, so as to realize circuit connection and function realization.
3. A connector is a component that connects electronic devices, cables or other devices through plugs and jacks. They can transmit information such as electricity, signals and data, and are widely used in computer, communication, automobile, aerospace and medical equipment. The composition of the connector A connector usually consists of two parts: a female head and a male head.