YK-Z high intelligent thermostat. This thermostat is a new generation of temperature control system designed and developed for users, with brand-new ideas and advanced electronic technology. Users must read the instructions before using them.
YK-Z thermostat adopts microcomputer processing chip for soft start, which makes the temperature control more accurate. In particular, multi-point temperature control can greatly reduce the cost. From at least 4 paragraphs to at most 128 paragraphs.
YK-Z thermostat adopts PIDD or PID control mode. There are two modes to choose from. PIDD is a temperature control technology, which can not only accurately control the temperature, but also extend the service life of the heater by 30%. Degree-day℃ or adjustable; The type of temperature sensing wire (thermocouple) is adjustable, J or K.
2. Temperature control principle of temperature control box The temperature control box is a device that keeps the required temperature value continuously. It mainly detects the temperature of the heating element through the intelligent computer chip (MCU) in the watch core, and then outputs the usual proportional current value through the data processing in the intelligent computer, thus achieving the purpose of temperature control.
PWM(PIDD) mode: Accurate temperature control can be achieved, but the noise of power supply is much louder than SSR mode. SR(PID) mode: The current noise is low, but the control ability of specific temperature is worse than that of PWM mode.
3.YK-B- 15A type:
Function Description ① The thermostat has the functions of soft start mode, manual mode and automatic mode. The soft start mode is preheating and dehumidification function, so that the heater will not be damaged due to the damp mold, thus prolonging the service life of the hot runner. ② The scale number can be adjusted in J or K; Degrees-days℃ or can be adjusted and displayed in the PV window. Temperature setting range is 34-534℃ ③ Input voltage is 220VAC 10% 50-60HZA or110VAC10% 50-60Hz A. ④ There are many alarm and protection functions: low temperature alarm. High temperature alarm. ※. ※ The temperature sensing line is disconnected to give an alarm. The temperature sensing wire is connected with the reversing alarm. Hot runner leakage protection alarm. ※. Hot runner short circuit and over power protection. ※. ※.
Description of 4.4. TMS-002 time sequence controller
main feature
1, which can directly and manually control the opening and closing of the needle valve.
Four time periods can be set, and the needle valve can be controlled to act twice in one working cycle (T3 and T4 can be set to 0 if a single action is needed).
2. The input signal can be switched or DC24V, and the position of jumper on the control card is easy to operate, which is suitable for the connection of various clamping signals.
3. The output signal can be selected from DC24V or AC220V, and there are two working modes: 0 and 1, with simple parameter setting and stable and reliable operation.
4. Working mode is A or B:
Mode A: Start working after receiving the input signal. If the time set by T 1, T2, T3 and T4 is not over, the input signal is disconnected and the controller will continue to work until T 1, T2, T3 and T4 are over.
Mode B: Start working after receiving the input signal. If the time set by T 1, T2, T3 and T4 does not end, the input signal will be disconnected and the controller will stop working. The factory setting is B mode.
5. There is no difference between positive and negative input signal wiring.
5.YKC680-4、YKC680-8
Command 1, operating environment 1) Starting power supply: AC220V/50-60Hz. 2) signal input power supply: DC24V or AC220V. 3) Output power of spiral needle valve: DC24V (below 1 00ma/door) or AC 220v (below1a) 2. PCB composition1) Controller PCB: power supply department, MICOM, input and output department. 2) Display PCB: display part and switch input part. 3. main control device 1) S.M.P.S: convert AC220V power supply into internal driving power supply DC24V/ 1A and dc5v/1a. 2) Microprocessor: output force control and display control. 3) Relay: spiral needle valve driving element (DC24V or AC220V output).