Usage of ultrasonic cleaning instrument
1. Installation of ultrasonic cleaning machine
Please refer to the installation instructions of the ultrasonic cleaning machine, connect the temperature sensor signal line, ultrasonic drive line, heater control line and other lines between the electric control cabinet and the main machine of the cleaning machine, and install the water inlet pipe, drain pipe and overflow drain pipe of the cleaning machine.
2. Parts placement of ultrasonic cleaning machine
Put the parts into the steel basket and gently put them into the cleaning pool. When placing a large number of parts at a time, try to make them evenly distributed in the basket without overlapping. The ultrasonic cleaner has been turned on.
When the ultrasonic cleaning machine works normally, ultrasonic waves are emitted from three directions at the same time. Press the ultrasonic start below, and the ultrasonic waves on both sides will start. Turn the power adjustment knob to the right, press the ultrasonic start, and adjust to the appropriate power.
At this time, the LEO display screen shows the current working power value of the bottom ultrasonic wave. 3. Stop the ultrasonic cleaning machine.
If you want to stop the machine during cleaning, you should first set the power knob to the minimum. Press again to stop the ultrasound. Control the cleaning time according to the cleaning surface.
4. Ultrasonic cleaning machine overflows
If there is too much floating oil on the surface of the cleaning pool, the overflow device of the cleaning machine should be turned on to remove it to prevent the secondary pollution of the cleaned workpiece. The specific operation is as follows: open the overflow drain valve, and inject water or cleaning liquid into the cleaning pool until the cleaning liquid begins to overflow (it is recommended to scrape the oil film in the direction of the overflow port with a scraper to promote its rapid outflow), and keep the overflow drain valve closed all the time to prevent the ground from being polluted by accidental overflow.
5. Post-treatment of ultrasonic cleaning machine
Take out the cleaned parts, thoroughly blow clean the residual cleaning solution in each hole with compressed air, and blow dry the surface (it is recommended to equip with a dust blower with an air compressor).
If conditions permit, it is best to configure a pool near the cleaning machine. So as to rinse the removed part. Necessity of using ultrasonic cleaning machine
Wearing plastic glasses for a long time, if the lenses are not cleaned, it is easy to be contaminated by bacteria and various microorganisms. People's tears contain a lot of protein and lipids.
Easy to attach to the lens, especially the synergistic arc is difficult to clean by hand. Wearing unclean lenses for a long time is easy to cause damage to the eyes and will also affect the effect of correcting vision. Based on the principle that ultrasonic generates high-frequency vibration, the ultrasonic cleaning machine can thoroughly and effectively clean the dirt in the cooperative arc, avoiding the inconvenience caused by manual cleaning of the lens and the phenomenon that the curvature of the lens changes and is damaged due to uneven stress in the cleaning process, and prolonging the service life of the lens.
Daily maintenance of ultrasonic cleaning instrument
1. Keep the workplace of ultrasonic equipment ventilated, dry and clean, which is conducive to the long-term efficient operation of the equipment and optimize the working environment conditions;
2. When the ultrasonic cleaning solution is too dirty, it should be handled in time, and the dirt in the cleaning tank and the liquid storage tank should be cleaned regularly to keep the inside and appearance of the ultrasonic cleaning tank clean, which can improve the durability of the cleaning tank;
3. The ultrasonic electric cabinet and equipment vents should be far away from water vapor, corrosive gas and dust, and the attached dust should be cleaned regularly with compressed air;
4. Test the insulation performance of ultrasound equipment regularly. Regularly check the aging electrical components and grounding wires to ensure that the equipment is well grounded. The project must be implemented by an electrician with professional experience;
5. Test the power supply regularly to confirm that it meets the power supply voltage requirements of the equipment, and avoid working for a long time under unstable power supply that is too high or too low;
6. For the equipment with filtering device, replace the filter element regularly;
7. For those with transmission mechanism, lubricants such as butter and engine oil should be added regularly as required, and gear oil of reducer should be replaced regularly to ensure that moving parts work under good lubrication conditions; Ultrasonic fault and abnormality.