Minutes of Fan Safety Production Accident Analysis Meeting
Date: 20xx year x month x day
Venue: 127 workshop meeting room
Moderator: Xu Xiangsheng
Participants: grass-roots managers of brewing workshop 127.
Meeting content: Strengthen safety production and raise safety awareness.
The meeting focused on workshop production and closely followed the four specific requirements for safety production:
1 and 127 workshop safety production management is a top-down management mode, and managers at all levels must pay special attention to safety links.
2. Emphasize the awareness of safety in production (the whole class can't just focus on production, thus ignoring safety), including safe driving on the way to and from work, and stop every three minutes instead of grabbing a second. There have been several traffic collisions in Brewing Workshop 3, but fortunately no one was seriously injured.
3. Before and after work, each shift should comprehensively check the existing dust collector and power cord. If abnormal phenomena are found, the workshop shall be informed in time, and the electric power maintenance personnel shall be dealt with immediately. It is forbidden to work with existing equipment in spite of illness.
4. Conduct pre-job safety training for new employees (due to work needs, new employees will be added to the workshop more or less, and the section chief and team leader should conduct post safety training for them in time, and ask the workshop to remind them of the safety handling requirements).
5. It is emphasized to wear labor protection articles, especially too much starch produced in the workshop, which will fall on the marble floor if it is not cleaned in time, which will cause slippage. Class members should pay attention to work anti-slip and wear shoes.
6. It is particularly emphasized that when operating the machine, the class members should strictly abide by the operating specifications and do not start the equipment or electrical appliances that are not operated by themselves.
7. In view of the current situation of safe production, the workshop has highlighted some bad behaviors that endanger the safety of the workshop, such as smoking and discarding cigarette butts. The workshop emphasizes that if you find smoking once, you will be fined 60 yuan/time, and if you find it again, no matter who it is,
Fines 120 yuan/time, accumulated in turn.
Minutes of safety production meeting: Mr. Ao Chunhua made a detailed analysis of the specific problems that occurred in April, focusing on the incident that some employees' families came to the workshop in April, and the dangerous incident that some shifts stood on the machine conveyor belt to clean the machines after work in the evening shift. Workshop requirements require team leaders to strengthen management to prevent accidents. Each section chief and monitor expressed their opinions and actively participated in the discussion on safety production.
Liu Yuehua, Ao Chunhua and Yang Xinlin also put forward requirements for the anti-slip function of the existing work shoe covers, suggesting that the company's work shoe covers must have anti-acid anti-slip function to protect employees from slipping and injury.
Ceng Zhiqiang, the squad leader, put forward constructive suggestions on employee safety training, standardized operation and improved insurance system. The monitor Luo put forward a novel idea for the construction of the security team? Master, new apprentice? The opinions on the responsibility of contracting safety have received positive responses from all participants.
Minutes of safety production meeting: Ao Chunhua and Liu Yuehua put forward many constructive suggestions on the existing workshop safety training, such as determining the operation skill specification. It has attracted the attention of the workshop and requires practical measures to be taken for adjustment and implementation in the future.
Finally, as the production safety supervisor of Brewing Workshop 127, I would like to introduce the personnel safety structure of Brewing Workshop 127 again: the safety team leader of Brewing Workshop127: Xu Xiangsheng, the deputy team leader: Ao Chunhua, the safety team members: Liu Yuehua, Yang Xinlin, and the monitor of each class. It is required to implement the responsibility of safety management in the future, and everyone should work together to improve the safety management level of the company.
Minutes of Fan Safety Production Accident Analysis Meeting
Meeting Agenda: Safety Work Meeting
Meeting time: xx year x month x day
Meeting contents:
A, electrical facilities installation regulations
The meeting stipulated the installation requirements of electrical facilities: in the future, all units must install electrical equipment and facilities according to the requirements of safety production standardization and unify the standards. For example, the equipment installation personnel should design and install according to the requirements of three-phase five-wire system, the front end of the socket of manual (mobile) tools should be equipped with leakage protection, and the power supply facilities such as socket board and control box should ensure that the PE line (zero line) is in place.
II. Work Arrangement of 20xx Annual Safety and Environmental Assessment
Combined with the actual situation of the Group, the annual safety and environmental assessment of 20xx has been adjusted on the basis of 20xx:
1. The assessment time is adjusted to: 20xx65438+1October1-20xx September 30th;
2. The company's major personal injury accident (referring to medical expenses) is adjusted to10.5 million yuan;
3. The total amount of safety EIA is adjusted to 654.38+10,000 yuan;
4.20xx annual safety and environmental accidents exceed the annual assessment indicators, and the penalty amount is adjusted to 50% of the excess (30% in 20xx);
Three. Other work notices
1.20xx annual safety production innovation declaration, if each unit meets the reward clauses in the safety production reward and punishment management system, it shall submit written materials to the safety supervision department of the logistics support center before 65438+February 10.
2. Each unit must complete the signing of the responsibility letter between the department and the security team at the end of 65438+February. The format of the responsibility book requires standardization, and the contents of the terms can be adjusted according to the actual situation of the unit on the basis of last year.
3. "Safety Management System" 3.3. 1 When employees go out during work, they must hold the leave application form or tolerance approval form approved by the superior supervisor of their unit for the record in the gatehouse. 3.3.2 Employees who take the shuttle bus to the north and south factories shall be supervised by the shuttle bus driver. If it is found that the bus driver gets off the bus halfway to do private affairs, he should give feedback to the safety supervision department of the logistics support center and notify the relevant units after investigation and verification. Starting from 65438+February 1, all guard rooms will be strictly implemented according to the system, and all units are requested to do relevant work.
Four, the next step to remind the safety work.
1. Through the standardization construction of safety production, the basic management data of each unit has been basically improved. Next, all units should rectify the existing problems in time, and the future work should be carried out in strict accordance with the standardization requirements.
2. Before the equipment installation and layout, all units should set out from the long-term development direction and arrange the equipment scientifically and reasonably according to the requirements of safety production standardization to avoid repeated rework.
3. Strengthen the safety production management of special equipment, and relevant responsible departments shall conduct safety inspection according to regulations and make records. For the equipment that needs inspection and testing, the responsible department must test it according to the regulations. Boilers, pressure vessels, lifting machinery, elevators, pressure gauges, safety valves, etc. Must be used during inspection.
4. Strengthen the safety production management of special operations personnel, and unlicensed personnel shall not work at their posts; The operation of certified personnel must be standardized and standard, and no illegal operation is allowed.
5. Strengthen the safety management of hazardous chemicals: users should designate special personnel and set posts, and they must be stored as required to strengthen the safety control during use.
6. In addition to the infrared protection of punching machines, units that can install protective nets on small punching machines should implement them in time.
Fan Wensan, Minutes of Safety Production Accident Analysis Meeting
Xxx (enterprise abbreviation) -C-AQB-JL00 1
Name of meeting: meeting of safety officers
Meeting time year month day afternoon meeting place
Records of major holders
Attending member
Meeting contents:
This meeting was chaired by xxxxx. At the meeting, according to the spirit of the regular meeting of cadres held by the general manager and some phenomena found in the recent supervision and inspection work, new arrangements were made for the next step.
1, safety supervision and inspection. From once a month to twice a month, the main participants, safety officers and principals give rectification instructions according to the inspection situation; Hold regular safety meetings at the end of each month to report the recent safety work.
2. Safety inspection system. On-site inspectors, safety officers, management personnel, etc. All parts shall be inspected and registered according to the system. The frequency of inspection is low, and those who do not follow the system will be punished according to relevant regulations; The rolling mill added a record book to the thin oil station, and the personnel checked and registered properly.
3. Factory vehicle management. At present, our company has a large number of vehicles, such as forklifts, transport vehicles, tractors, excavators, commercial vehicles and so on. Therefore, it is necessary to strengthen the supervision and management of on-site personnel, especially construction vehicles, to explore the construction site, and to stop or notify the security department to deal with violations.
4. Conduct pre-job training for safety leaders and special operations personnel in different regions. Special steel and high-speed wire rod will be put into production soon, and now all regions should set up part-time safety leaders; The safety operation procedures of each post should be compiled into a book, and employees should be trained in a targeted manner.
5, homework ticket use. At present, there are many aerial work, hot work and confined space work, but the use of individual work tickets is not in place. People at all levels sign the working ticket, which also informs you to check its preventive measures and arrange personnel to check and assist, and also reflects the importance attached to safety. If the next inspection finds that the operation ticket has not been handled, it will be punished according to the regulations, and if the illegal operation is found, the punishment will be doubled.
6. Safety signs on the project wall. Now that the high-speed rail has been partially completed, it should be used as soon as possible, especially the gas station, power distribution room, operation desk and other parts, which will be tested soon to serve as a warning to operators and outsiders; Some special steel safety signs should be made after collection; The marking of new factory buildings must be carried out according to the promulgated national laws and regulations.
7. Smoking is strictly prohibited. At present, people have been arranged to conduct inspections every day, and occasional surprise inspections at night. If anyone is found smoking at the scene, it will be handled according to the regulations. No matter what happens, everyone should be informed in place, including our employees and foreign construction teams.
8, lightning protection self-inspection. Each factory uses the key table to do self-inspection on the grounding of gas station and power distribution room to see whether the grounding meets the requirements; At present, in order to reduce the damage of lightning and static electricity to electrical appliances or lines, some units have installed surge devices in dangerous parts such as gas stations to prevent damage. Let's see if we should install them.
9. Summer is coming, so we should do a good job in heatstroke prevention and gutter cleaning. Measures such as increasing part of cooling water for employees; Some equipment should be checked; The driving temperature is high, so it is necessary to check and maintain the air conditioner and urge the new driving air conditioner on the project. Before the rainy season comes, it is necessary to clean the gutter and the sink on the top of the workshop, repair the damaged downspout, and prevent rainwater from recharging or getting wet. The low-lying temporary lines of the construction team of this project should be cleaned up to prevent accidents.
10, traffic safety. Some new employees have entered the project one after another, emphasizing traffic safety. At the same time, it is necessary to issue a receipt now, so that they can form good habits from the beginning.
Report to xxx General Manager for approval.
Send members of the security Committee
Issued to all safety management personnel on.
I guess you like it.
1. minutes of safety accident analysis meeting
2. Model essay on meeting minutes of production safety accidents
3.6 Factory safety meeting record template.
4. There are 6 model essays on the minutes of the regular meeting of production safety.
5.6 Model essay on record of safety production meeting.
6.20 17 model essay on minutes of safety production meeting