1, according to the operating panel test key to observe the status of the ammeter: ① no current: check the laser power supply power supply is connected, whether the high-voltage line is loose or off, whether the signal line is loose; ② current: check whether the lens is broken, whether the optical path is seriously offset;
2, check whether the water circulation system: ① no water: check whether the water pump is damaged or not energized; ② water: check the water inlet, outlet is connected to the reverse or water pipe is normal. No water: check whether the water pump is damaged or not energized; ② water: check whether the water inlet, outlet is connected to the reverse or water pipe rupture;
3, can point shooting, can self-test, send data does not light (check whether the computer settings are correct).
Second, VDIAO micro-carving laser engraving machine engraving depth is not the same or engraving is not deep
1, check the water circulation system water flow is smooth (water pipe bends or water pipe rupture);
2, check whether the focal length of the normal (recalibrated);
3, check the light path is normal (recalibrated);
4, check whether the plate on the laying of paper Whether too thick, whether the amount of water is too much (recorrection);
5, check whether the beam is parallel (adjust the two sides of the belt)
6, check whether the lens is broken (replacement);
7, check whether the lens or the emitting end of the laser tube is contaminated (recleaned);
8, check whether the temperature of the water is higher than 30 ° C (replacement of circulating water);
< p>9, check whether the laser head or focusing mirror is loose (tighten);10, the laser current light intensity must reach 8mA;
11, laser tube aging.
Three, VDIAO micro-engraving laser engraving machine reset is not normal
1, check whether the sensor is dusty, poor contact or damaged (wipe the dust on the sensor or replacement);
2, check whether the flexible guide tape data line is poor contact or damage (trim the data line to re-plugging or replacement of the data line);
3, check whether the ground contact is Reliable or high-voltage line is damaged (re-grounding or replace the high-voltage line);
4, poor contact with the motor line.
Four, VDIAO micro-engraving laser engraving machine leakage
1, initialization is not correct, the data has been sent (corrected);
2, the order of operation is reversed (re-output);
3, static interference (check whether the ground wire is off).
Fifth, VDIAO micro-engraving laser engraving machine cleaning hook edge misplaced, not closed
1, edited the document is correct (re-edit);
2, whether the selected target is beyond the layout (re-selected);
3, check the software parameters are set correctly (reset);
4, the computer system is incorrect ( Reinstall the operating system and software);
5, check whether the left and right belt elasticity is the same or the rear end of the belt is too loose (belt tightening);
6, check whether the belt or synchronous wheel slipping, jumping teeth (tighten the synchronous wheel or belt);
7, check whether the beam is parallel (re-adjustment of left and right belts);
Six, the computer can not be output
1, check whether the software parameter settings are normal (reset);
2, whether the engraving machine is the first to press the positioning of the start and then output (re-output);
3, check whether the machine was not reset beforehand (recorrected);
4, check whether the output serial port is the same as the software settings serial port (reset);
5, check whether the ground line is reliable, whether the static interference data line (re-grounding);
6, replace the computer serial port output test;
7, reinstall the software and reset the test;
8, formatting the computer system disk to reinstall the software test;
9, the motherboard serial port damage to be repaired or replaced.
7, can not calculate the path
1, check to set the path of the calculation method is correct;
2, check the graphics file format is correct (recorrected);
3, uninstall the software to reinstall and set up;
eight, common computer problems
1, the font gradually decreases (reinstall the operating system);
2, the amount of data is too large to calculate the laser path (wait for a period of time or increase the computer memory);
3, the calculation of the path for a long time did not respond to, restart the computer test.
VDIAO micro-engraving laser cutting machine dedicated to your service