2 is the rated voltage of AC 220V or 110V, the frequency is 50HZHZ, vibrating plate according to the need to use a full-wave or half-wave excitation. 3 is the vibrating disk according to customer needs can be divided into clockwise and counterclockwise.
Vibrating plate installation: 1 hit the packaging to check whether the machine and accessories with the packing list 2 is to check whether the host parts of the firmware is loose. 3 is to make sure that the vibration plate is installed in a way that reduces the frequency of the vibration. 3 is the installation must make the vibration damping components in the relative position.
4 is the vibration plate height and level adjustment, the base of the poly solid in the fixed plate or bracket. 5 is the vibration plate export even connected to the equipment to be left between the appropriate clearance, so as not to affect the normal operation of the vibration plate.
6 is the electrical control box connected to the vibrating plate electrical plug, turn on the power, open the switch, slowly turn the potentiometer,
gradually reach the required number of materials can be fed. Finally, it should be noted that before starting the potentiometer must be adjusted to the lowest value, so as to avoid damage to the silicon controlled vibrating disk common failures and troubleshooting methods are as follows:
A. Turn on the power does not vibrate, to check the electrical controller fuse is dissolved, whether the electrical components are loose, plug socket is poor contact. If the conveyor speed is not up to the requirements and pay attention to the following three;
1. Check the fastening of the elastic components of the screws are loose. 2. 2. Whether the spring plate is broken. 3. Electromagnetic gap is too large, the normal gap corresponds to a small vibrating plate electromagnet and armature spacing in the range of 0.5MM to 1.2MM.
The core and armature work surface is not parallel to the degree of not more than 0.02MM. ii. Solenoid coil temperature is high or burned coil has 2 points: 1. electromagnetic and armature spacing between the coil is too large, easy to burn.
2. Adapted to the full-wave vibration electromagnet if used for half-wave power will appear high temperature. All of the above is the application and maintenance of the vibration plate, may not be comprehensive and look forward to improving.
The technical parameters of the vibrating plate are three: 1 is the top of the plate specifications are roughly φ80MM to φ1000MM.
2 is the rated voltage of 220V or 110V AC, the frequency is 50Hz, the vibrating plate according to the need for full-wave excitation or half-wave excitation. 3 is the vibrating disk according to customer needs can be divided into clockwise and counterclockwise.
Vibrating plate installation: 1 hit the packaging to check whether the machine and accessories with the packing list 2 is to check whether the host parts of the firmware is loose. 3 is to make sure that the vibration plate is installed in a way that reduces the frequency of the vibration. 3 is the installation must make the vibration damping components in the relative position.
4 is the vibration plate height and level adjustment, the base of the poly solid in the fixed plate or bracket. 5 is the vibration plate export even connected to the equipment to be left between the appropriate gap, so as not to affect the normal operation of the vibration plate.
6 is the electrical control box connected to the vibrating plate electrical plug, turn on the power, open the switch, slowly turn the potentiometer,
gradually reach the required number of materials can be fed. Finally, it should be noted that before starting the potentiometer must be adjusted to the lowest value, so as to avoid damage to the silicon controlled vibrating disk common failures and troubleshooting methods are as follows:
A. Turn on the power does not vibrate, to check the electrical controller fuse is dissolved, whether the electrical components are loose, whether the plug socket is poor contact. If the conveyor speed is not up to the requirements and pay attention to the following three;
1. Check the fastening of the elastic components of the screws are loose. 2. 2. Whether the spring plate is broken. 3. Electromagnetic gap is too large, the normal gap corresponds to a small vibrating plate electromagnet and armature spacing in the range of 0.5MM to 1.2MM.
The core and armature work surface is not parallel to the degree of not more than 0.02MM. ii. Solenoid coil temperature is high or burned coil has 2 points: 1. electromagnetic and armature spacing between the coil is too large, easy to burn.
2. Adapted to the full-wave vibration electromagnet if used for half-wave power will appear high temperature. All of the above is the application and maintenance of the vibration plate, may not be comprehensive and look forward to improving.